Search published articles


Showing 23 results for Casting

Saghi S., Divandari M., Kharazi Y.h.k.,
Volume 1, Issue 2 (6-2004)
Abstract

The effects of gating system and pattern geometry on the metal flow in the lost foam casting (LFC) process have been investigated using glass covered mold and video recording system. Unlike convectional casting process, the type of the gating system showed little effect on fillability in lost foam, but pattern thickness had large effect on mold filling. The mold filling behavior seems to be controlled by the combined influences of heat and mass transfer. The flow rate increased with increasing pattern thickness.
Javadpour J., Sakhaii K., Masihiyanpour A.a.,
Volume 1, Issue 4 (12-2004)
Abstract

Thin sheets of hydroxyapatite were fabricated by tape casting process. The non-aqueoustape casting formulation was optimized by adjusting the concentration of organic additivesspecially those of binder and plasticizer in the slurry. The optimized slurry was cast on a glasscarrier using a designed laboratory scale doctor blade. Following a binder removal stage, thetapes were sintered at different temperatures in air atmosphere. Heat treatment at 1250 °C led tothe formation of a dense microstructure as was evidenced by the scanning electron microscopy.
Attar E., Babaei R., Homayonifar P., Asgary K., Davami P.,
Volume 1, Issue 4 (12-2004)
Abstract

During mold filling, molten metal can only advance as quickly as the air inside thecavity is expelled. In this work an analytical model describing air flow is developed based on aincompressible flow theory. Air pressure has serious effects upon the filling behaviour such assurface profile and filling time. In this work a new mathematical model is proposed for calculationthe air pressure during the mold filling. A single phase computational fluid dynamic code based onthe SOLA-VOF algorithm used for prediction the fluid flow. Air discharged through the vents ismodelled by ideal gas assumption, conservation of mass equation and Bernoulli law. A newalgorithm was developed to interpolates the air pressure on the surface cell. The creation of airback pressure was correlated with sizes of vents and pouring basin height. In order to verify thecomputational results a series of experimental test was conducted. Comparison between theexperimental data and simulation results has shown a good agreement.
Kharazi Y.h.k., Divandari M.,
Volume 2, Issue 1 (3-2005)
Abstract

The mold-filling behavior in the casting of aluminum alloy (A413) using lost foam casting (LFC) was explored. The effects of gate numbers, type of gating and casting thickness on the filling behavior were evaluated. Although, unlike convectional casting process, the gating system showed little effect onfilling ability, casting thickness created a greater effect on the mold filling. In contrast with convectional casting process, the mold filling seems to be controlled by castinggeometry as a consequence of combined influence of heat and mass transfer. The melt used to enter from the first gate instead of last gate which is in contrast with convectional casting process.
Arabi H., Divandari M., Hosseini A.h.m.,
Volume 3, Issue 3 (12-2006)
Abstract

In this research the influence of Ti contents on the amounts of inclusions formation and mechanical properties of a high alloy high strength steel, C300, has been investigated. For this purpose several bars were casted under the same solidification conditions, but different amounts of Ti element. All the seven casted bars were homogenized at 1200°C for a period of 2 hours. Then, they were immediately hot rolled after homogenization so that the out rolling temperature was kept in the range of 1000-1200° C. The specimens were then solution annealed at 820°C for hour and finally they were aged for a period of 3 hours at 500°C. The samples were subjected to tensile, impact and hardness tests in order to relate the variation in volume percent of inclusions due to different amount of Ti, to mechanical properties. The results showed that by increasing the amount of Ti a serious decline in toughness properties of the alloy due to increase in inclusion population occurred. So this research provides a very useful information about the relation between volume fraction of inclusions and mechanical properties of a C300 high strength steel.
M. Ghalambaz, M. Shahmiri,
Volume 5, Issue 3 (9-2008)
Abstract

Abstract: Cooling slope-casting processing is a relatively new technique to produce semisolid cast feedstock for the thixoforming process. Simple equipment, ease of operation, and low processing costs are the main advantages of this process in comparison with existing processes such as mechanical stirring, electromagnetic stirring, etc. The processing parameters of cooling slope casting are length, angle and the material of the inclined plate and their combinations, which usually affect the micro structural evolutions of the primary solid phase. In order to clarify the effect of the processing parameters on the evolution of the particle size, based on experimental investigation, Artificial Neural Network (ANN) was applied to predict the primary silicon crystals (PSCs) size of semisolid cast ingot via a cooling slope casting process of Al-20%(wt.%) Si alloy. The results demonstrated that the ANN, with 2 hidden layers and topology (4, 3), could predict the primary particle size with a high accuracy of 94%. The sensitivity analysis also revealed that material of the cooling slope had the largest effect on particle size.
S. Kianfar,, S. H. Seyedein, M. R.aboutalebi,
Volume 5, Issue 4 (12-2008)
Abstract

Abstract: The horizontal continuous casting process has received a significant attention for near net shape casting of non ferrous metals and alloys. Numerical Simulation has been widely used for process design and optimization of continuous casting process. In the present study, a 3-dimensional heat flow model was developed to simulate the heat transfer and solidification in a horizontal billet continuous casting system in which the air gap formation and its effect on heat extraction rate from solidifying billet was also considered. In order to test the developed model, it was run to simulate the heat transfer and solidification for an industrial billet caster. The predicted temperature distribution within the mold and billet was compared with those measured on the industrial caster in which a good agreement was obtained. Finally, parametric studies were carried out by validated model to evaluate the effects of different parameters on solidification profile and temperature distribution within the model brass billet. The microstructure of cast billet was analyzed to determine the secondary dendrite arm spacing (SDAS) under different cooling conditions. Based on measured SDAS and predicted solidification rate a correlation between SDAS and cooling rate was proposed for continuously cast brass billet.
A. H. Shafie Farhood, F. Akhlaghi,
Volume 7, Issue 1 (3-2010)
Abstract

Abstract:

structures in alloys. This method is based on pouring the melt through a small sized nozzle into a mould located at a

certain height under the crucible. This simple method generates globular structures without using equipments such as

impellers, electromagnetic stirrers, ultrasonic probes and cooling slopes. Therefore it is cost effective. In the present

study, the effect of casting size and mould casting modulus on the globular structure evolution in A356 aluminium alloy

specimens prepared by NMS process was investigated. The results showed that regardless of the different casting

modulus and their sizes, all the specimens exhibited globular structures. However, the size and shape factor of the

globules decreased with increased casting modulus and casting size indicating the influential effect of the surface area

of the mould in generating globular structures in this process.

Narrow Melt Stream (NMS) is a relatively new semisolid metal processing technique for producing globular

A. Jafaria, S. H. Seyedeina, M. R. Aboutalebia, D. G. Eskinb, L. Katgermanb,
Volume 7, Issue 3 (8-2010)
Abstract

ABSTRACT Macrosegregation has been received high attention in the solidification modeling studies. In the present work, a numerical model was developed to predict the macrosegregation during the DC Casting of an Al-4.5wt%Cu billet. The mathematical model developed in this study consists of mass, momentum, energy and species conservation equations for a two-phase mixture of liquid and solid in an axisymmetric coordinates. The solution methodology is based on a standard Finite Volume Method. A new scheme called Semi-Implicit Method for Thermodynamically-Linked Equations (SIMTLE) was employed to link energy and species equations with phase diagram of the alloying system. The model was tested by experimental data extracted from an industrial scale DC caster and a relatively good agreement was obtained. It was concluded that a proper macrosegregation model needs two key features: a precise flow description in the two-phase regions and a capable efficient numerical scheme
W. Orlowicz, M. Tupaj, M. Mróz, J. Betlej, F. Ploszaj,
Volume 9, Issue 1 (3-2012)
Abstract

Abstract: This study presents the research results of effect that refining process has on porosity and mechanical properties of high pressure die castings made of AlSi12S alloy. The operation of refining was carried out in a melting furnace with the use of an FDU Mini Degasser. Mechanical properties (UTS, YS, Elongation, Brinell Hardness) were assessed on samples taken from high pressure die castings. The effect of molten metal transfer operation and the time elapsing from completion of the refining process on the alloy mechanical properties was determined.
M. Alipour, S. Mirjavadi, M. K. Besharati Givi, H. Razmi, M. Emamy, J. Rassizadehghani,
Volume 9, Issue 4 (12-2012)
Abstract

In this study the effect of Al–5Ti–1B grain refiner on the structural characteristics and wear properties of Al–12Zn–3Mg–2.5Cu alloy was investigated. The optimum amount for Ti containing grain refiners was selected as 2 wt.%. T6 heat treatment, (i.e. heating at 460 °C for 1 h before water quenching to room temperature and then aging at 120 °C for 24 h) was applied for all specimens before wear testing. Dry sliding wear resistant of the alloy was performed under normal atmospheric conditions. The experimental results showed that the T6 heat treatment considerably improved the resistance of Al–12Zn–3Mg–2.5Cu alloy to dry sliding wear.
N. Najmoddin, H.r. Rezaie, A. Beitollahi, M.s. Toprak,
Volume 11, Issue 3 (9-2014)
Abstract

The synthesis of mesoporous CuFe2O4 spinel by several nanocasting strategies (i.e., multi-step nanocasting, one step nanocasting, modified solid-liquid), in which copper and iron nitrates are used as precursors and Pluronic P123 as surfactant, is explored. We have also checked the effect of pH, citric acid and sodium citrate in multi-step nanocasting method. The modified solid-liquid method which contains impregnating mesoporous silica by molten state salts in a non-ionic solvent seems to be the best choice to obtain single phase ordered mesoporous copper ferrite. Other methods suffer from the presence of copper oxide or hematite as impurities or lack of integrity in the mesoporous structure. Increasing pH up to 9.5 does not enhance the phase formation inside the pores of the silica matrix. The citric acid yields a fine structure but does not facilitate the phase formation. Adding sodium citrate neither heals the phase formation nor the structure of the final product. Moreover, vinyl- functionalized mesoporous silica exploited in this study as a hard template entraps both metal nitrates in the pores, assisting impregnation procedure
A. Fattah-Alhosseini, M. Ranjbaran, S. Vajdi Vahid,
Volume 12, Issue 2 (6-2015)
Abstract

In this study, corrosion behaviour of A356-10 vol.% SiC composites casted by gravity and squeeze casting is evaluated. For this purpose, prepared samples were immersed in HCl solution for 1h at open circuit potential. Tafel polarization and electrochemical impedance spectroscopy (EIS) were carried out to study the corrosion resistance of composites. The Tafel polarization and EIS studies of the corrosion behaviour of the A356-10 vol.% SiC composites showed that the corrosion resistance of the composite casted by squeeze casting was higher than that of the composites casted by gravity in selected corrosion media. Also, the Tafel polarization and EIS studies revealed that the corrosion current densities of both composites increase with the increase in the concentration of HCl. The micrographs of scanning electron microscope (SEM) clearly showed the squeeze casting composite exhibits a good dispersion/matrix interface compared to that of the composites produced by gravity casting
M. Alipour, M. Emami, R. Eslami Farsania, M. H. Siadati, H. Khorsand,
Volume 12, Issue 4 (12-2015)
Abstract

A modified strain-induced melt activation (SIMA) process was applied and its effect on the structural characteristics and hardness of the aluminum alloy Al–12Zn–3Mg–2.5Cu was investigated. Specimens subjected to a deformation of 40% at 300 °C were heat treated at various times (10-40 min) and temperatures (550-600 °C). Microstructural studies were carried out using optical and scanning electron microscopies (SEM). Results showed that the best microstructure was obtained at the temperature and time of 575 °C and 20 min, respectively. The hardness test results revealed superior hardness in comparison with the samples prepared without the application of the modified SIMA process.

T6 heat treatment including quenching to 25 °C and aging at 120 °C for 24 h was employed to reach to the maximum strength. After the T6 heat treatment, the average tensile strength increased from 231 MPa to 487 and 215 MPa to 462 for samples before and after strain-induced melt activation process, respectively. Ultimate strength of globular microstructure specimens after SIMA process has a lower value than as-cast specimens without SIMA process


N. Maragani, K. Vijaya Kumar,
Volume 15, Issue 4 (12-2018)
Abstract

An attempt has been focused to develop a new aluminum ion conducting non aqueous polymer electrolyte for high power rechargeable batteries having applications in rapidly growing markets, such as laptops, handy tele communication equipments, electric vehicles, camcorders, etc. These features have given a thrust to develop a suitable Nano composite GPE based on  PAN as polymer host and Sodium fluoride (NaF) as dopant salt and Al2O3 as nano filler in the form of thin films through solution casting technique consuming N,N-dimethyl formamide (DMF) as a common solvent. NCGPE films have been prepared by solution casting technique. The XRD pattern of 70PAN-30NaF with addition of wt% Al2O3 ceramic filler indicates reducing degree of crystallinity. Using IR studies revealed that the complexation of the polymer poly (acrylonitrle) with NaF. The conductivity of the GPEs was studied with enhancement of nano fillers. The sample containing 3% of Al2O3 exhibits the highest conductivity of 4.82x10-3S cm-1 at room temperature (303K) and 5.96x10-3S cm-1 at 378K. With the help of Wagner’s polarization technique electronic (te) and ionic (ti) values can be determined.To determine profiles of discharge characteristics (70PAN-30NaF-3wt% Al2O3) NCGPE solid-state electrochemical cell was fabricated and various cell profiles were evaluated

S. Kord, M. H. Siadati, M. Alipour, H. Amiri, P.g. Koppad, A. C. Gowda,
Volume 15, Issue 4 (12-2018)
Abstract

The effects of rare earth element, erbium (Er) additions on the microstructure and mechanical properties of Al-15Zn-2.5Mg-2.5Cu alloy have been investigated. This new high strength alloy with erbium additions (0.5, 1.0, 1.5 and 2.0 wt%) was synthesized by liquid metallurgy route followed by hot extrusion. Microstructural characterization was performed using scanning electron microscope and electron probe microanalysis. Significant amount of grain refinement was observed with erbium addition in the hot extruded and heat treated alloy. Tensile test was performed to investigate the effect rare earth on mechanical behavior of alloy in as cast and hot extruded condition before and after T6 heat treatment. The combined effect of erbium addition, hot extrusion and heat treatment significantly enhanced the tensile strength of alloy (602 MPa) when compared to the as cast alloy without erbium addition (225 MPa). The strengthening of the alloy was attributed to grain refinement caused by erbium along with hot extrusion and formation of precipitates after T6 heat treatment. Fractograhic investigations revealed that the hot extruded alloy with erbium addition after heat treatment showed uniformly distributed deep dimples exhibiting ductile behavior. 
 

M. Gholami, M. Divandari,
Volume 15, Issue 4 (12-2018)
Abstract

Centrifugal casting process, in both horizontal and vertical mode, is considered as an efficient method to produce bimetallic components. Al/Cu65Zn35 couples were prepared by the vertical centrifugal casting process. In this study, different volume of molten aluminum having melt-to-solid (m/s) volume ratios (VR) of 1.5 and 2.5, were cast into preheated brass bush rotating at 800, 1600, and 2000 (rpm), respectively. The thickness of the interface, which is composed of three different zones, is depended on the rotational speed and the (VR) and was at least 490µm (at VR=1.5 and 2000 rpm) and at most 1480 µm (at VR=2.5 and 800 rpm). The results of optical microscopy, energy dispersive X-ray spectroscopy (EDS), and X-ray diffraction analysis showed that the interface layers are composed of Al2Cu5Zn4, Al3Cu3Zn, Al2Cu precipitates dispersed in the matrix and finally α-Al/Al2Cu anomalous eutectic structure near the aluminum side. Gas pore entrapment and oxide film entrainment defect was detected within the interface next to the aluminum base metal.

M. Tavakoli Harandi, M. Askari-Paykani, H. Shahverdi, M. Nili Ahmadabadi,
Volume 16, Issue 1 (3-2019)
Abstract

One-step and two-step annealing techniques were used to examine the relationship between microstructure and mechanical properties during compression tests in iron-based ribbons and nanostructured 1- and 2.5mm cylindrical rods. The X-ray diffraction, microstructural, and mechanical results showed that substituting Nb for Fe had a minor effect on glass-forming ability but increased the formability index. The novel two-step annealing process resulted in a remarkable formability index of 16.62 GPa, yield stress of 2830 MPa, ultimate strength of 3866 MPa, and 4.3% plastic strain. A ductile nanosized α-Fe framework and boron-containing nano precipitations, which caused Zener pinning effect, were responsible for these novel mechanical properties.

M. Senthil Kumar , R. V. Managalaraja, K. Senthil Kumar, L. Natrayan,
Volume 16, Issue 2 (6-2019)
Abstract

The present requirement of automobile industry is seeking lightweight material that satisfices the technical and technological requirements with better mechanical and tribological characteristics.  Aluminium matrix composite ( AMC ) materials meet the requirements of the modern demands. AMCs are used in automotive applications as engine cylinders, pistons, disc and drum brakes. This paper investigates the effect of particle size and wt% of Al2O3/SiC reinforcement on mechanical and tribological properties of hybrid metal matrix composites (HMMCs). AA2024 aluminium alloy is reinforced with Al2O3/SiC different particle sizes (10, 20 and 40 µm) and weight fractions (upto 10 wt %) were fabricated by using squeeze casting technique. HMMCs were characterized for its properties such asX-ray diffraction (XRD), density, scanning electron microscope ( SEM ), hardness, tensile strength, wear and coefficient of friction. AA2024/5wt%Al2O3/5wt%SiC with 10 μm reinforced particle size showed maximum hardness and tensile strength 156.4 HV and 531.43 MPa and decrease in wear rate was observed from from 0.00307 to 0.00221 for 10N. Hybrid composites showed improved mechanical and wear resistance suitable for engine cylinder liner applications.
Tamilanban Thangaraju, Thirupandiyur Selvanambi Ravikumar, Sivaraman Kanthasamy,
Volume 18, Issue 4 (12-2021)
Abstract

The effect of pouring temperature while preparing Al SiC metal matrix composites, with additional benefits of magnesium and copper through stir casting technique were investigated. The composites were fabricated by mixing 12 wt% of SiC reinforcements, 4 wt% magnesium and 2 wt% copper into 6061 aluminium alloy melt at different pouring temperatures (630 ºC, 670 ºC and 710ºC). The addition of magnesium will enhance the wettability of the SiC particles with Al matrix and subsequently increase its interface bonding strength. The inclusion of copper has considerable improvement in strength and hardness of the composite. The microstructure and mechanical properties (tensile strength and hardness) of the Al MMC are evaluated with the corresponding processing parameter, specifically pouring temperature of the cast composite. The metallurgical characterization utilizing optical and scanning electron microscope were observed for the prepared composites. The coarse microstructure and homogenous distribution of alloying elements along with SiC particles were appeared within dendrite structures of the Al SiC composites. The SiC particles has effectively distributed and produced better bonding strength in composites prepared with 670ºC pouring temperature. Higher tensile strength and maximum hardness have occurred in composite at pouring temperature of 670ºC as compared to other composites. The mechanical properties were lower in composites prepared using lesser pouring temperature (630ºC) and significantly decreased for higher pouring temperature (710ºC) of the composites.
 


Page 1 from 2    
First
Previous
1
 

© 2022 All Rights Reserved | Iranian Journal of Materials Science and Engineering

Designed & Developed by : Yektaweb