Search published articles


Showing 5 results for Sharma

P.k. Jayashree, Sh. Raviraj, S.s. Sharma, G. Shankar,
Volume 15, Issue 2 (June 2018)
Abstract

CoHErrelation between weldability and improvement in properties is a key issue in materials science research. The objective of this work is to optimize the process parameters viz., aging temperature, aging time, solutionizing time, to enhance the hardness of Al6061 alloy. Hence, the present paper deals with hardness study of Tungsten Inert Gas welded 6061 aluminium alloy after age hardening under three different aging temperatures, aging time and solutionizing time using Taguchi’s L9 Orthogonal array. Finally, a second order model has been generated for hardness using Response Surface Methodology with 20 runs for full design. The predicted and experimental results are in good agreement.

R. Kumar, Y. Chandra Sharma, V. Vidya Sagar, D. Bhardwaj,
Volume 17, Issue 2 (June 2020)
Abstract

In this study an effort has been made for the plasma ion nitriding (PIN) of Inconel 600 and 601 alloys at low temperatures. After plasma ion nitriding, microstructure study, growth kinetics of nitrided layer formation and wear properties were investigated by various characterization techniques such as; scanning electron microscope (SEM), X-ray diffraction (XRD) analysis, micro-hardness measurement and wear test by pin on disk technique. It was found that, surface micro-hardness increases after PIN process. A mix peak of epsilon (ε) phase with fcc (γ) phase was detected for all temperature range (350 0C to 450 0C), while the chromium nitride (CrN) phase was detected at elevated temperature range ~450 0C in inconel 601 alloy. The calculated values of diffusion coefficient and activation energy for diffusion of nitrogen are in accordance with the literature. Volume loss and wear rate of the plasma nitrided samples decreases, but it increases as PIN process temperature increases.

Yogesh Dewang, Vipin Sharma,
Volume 18, Issue 1 (March 2021)
Abstract

Finite element analysis has been carried out to investigate the effect of various parameters on axisymmetric hot extrusion process using aluminum alloy. The objective of the present work is to investigate the effect of friction coefficient, die angle, die-profile radius and predefined temperature of workpiece through FEM simulation of extrusion process. Nodal temperature distribution, heat flux, peak temperature at nodes and peak flux induced are identified as the output variables to assess the thermo-mechanical deformation behavior of aluminum alloy. Mesh sensitivity analysis is performed for the evaluation of mesh convergence as well as depicts the accuracy of present FEM model. Higher will be the coefficient of friction between interacting surfaces of die-billet assembly, more will be the increment in nodal temperature in billet. Higher will be the coefficient of friction, higher will be the generation of heat flux within billet, as this is achieved for highest coefficient of friction. Peak nodal temperature diminishes with increase in die profile radius nearly by 17 %.Maximum heat flux diminishes non-linearly by 30% with increase in die profile radius. Maximum nodal temperature increases nearly linearly by 14% with increment in predefined temperature of billet. Maximum heat flux decreases non-linearly by 5 % with increment in the initial temperature of workpiece. Validation of present numerical model is established on the basis of deformation behavior in terms of evolution of nodal temperature distribution upon comparison with previous studies available in literature.


Namrata Saxena, Varshali Sharma, Ritu Sharma, Kamlesh Kumar Sharma, Kapil Kumar Jain,
Volume 18, Issue 2 (June 2021)
Abstract

The work reported in this paper was focused on the investigation of surface morphological, microstructural, and optical features of polycrystalline BaTiO3 thin film deposited on p-type Si < 100 > substrate using e-beam PVD (physical vapor deposition) technique. The influence of annealing over the surface morphology of the thin film was analyzed by X-ray diffraction, atomic force microscopy and scanning electron microscopy characterization methods. When the annealing temperature was increased from as-deposited to 800 °C there was a significant growth in the grain size from 28.407 nm to 37.89 nm. This granular growth of BaTiO3 made the thin film appropriate for nanoelectronic device applications. The roughness of the annealed film got increased from 31.5 nm to 52.8 nm with the annealing temperature. The optical bandgap was computed using Kubelka-Munk (KM) method which got reduced from 3.93 eV to 3.87 eV for the as-deposited to the 800 °C annealed film. The above reported properties made the annealed film suitable for optoelectronic applications. For polycrystalline BaTiO3 thin film the refractive index varied from 2.2 to 1.98 from 400 to 500 nm and it was 2.05 at 550 nm wavelength. The broad peaks in Raman spectra indicated the polycrystalline nature of the thin film. It had been also observed that with the annealing temperature the intensity of the Raman bands got increased. From these results, it was proved that annealing significantly improved the crystallinity, microstructural, surface morphological and optical features of the barium titanate thin film which made it suitable as sensors in biomedical applications as it is cost-effective, lead-free and environment friendly material.
Sravanthi Gudikandula, Ambuj Sharma,
Volume 19, Issue 4 (Desember 2022)
Abstract

The lean duplex stainless steels (LDSS) have excellent features due to the microstructural phase
combination of austenite and ferrite grains. These steels have low Ni and Mo contents which can reduce the cost
and stabilize the austenite fraction in the microstructure. In recent years, welding is used to enhance the
microstructural behaviour of LDSS. In this paper, Gas tungsten arc welding (GTAW) was performed on LDSS
S32101 with different heat energy inputs and varying welding currents. The influence of heat inputs (0.85 and 1.3
kJ/mm) on welded samples was investigated to study the microstructural behaviour, phase balance, and mechanical
& corrosion performance. The microstructures studies were carried out using an optical microscope, scanning
electron microscope and X-ray diffraction. The effect of Heat input led to the significant microstructural evolution
in weld metals with high austenite reformation. The microstructure of weldments consisted of inter-granular
austenite (IGA), grain boundary austenite (GBA) and Widmanstatten austenite (WA). Important mechanical
properties such as tensile strength and micro-hardness were investigated to understand the performance of
weldments. The polarization method was used to understand the corrosion behaviour of weldment in a 3.5% NaCl
solution. The experimental results showed enhanced properties of welds that could be suitable for industrial
applications.

Page 1 from 1     

© 2022 All Rights Reserved | Iranian Journal of Materials Science and Engineering

Designed & Developed by : Yektaweb