Showing 10 results for Optical Properties
Nadjet Aklouche, Mosbah Ammar,
Volume 20, Issue 1 (3-2023)
Abstract
This work aims to prepare and study amorphous carbon nitride (CNx) films. Films were deposited by reactive magnetron radiofrequency (RF) sputtering from graphite target in argon and nitrogen mixture discharge at room temperature. The ratio of the gas flow rate was varied from 0.1 to 1. Deposited films were found to be amorphous. Highest Nitrogen concentration achieved was 42 atomic percent which is very rare and therefore, the highest nitrogen to carbon atomic ratio was 0.76. The incorporation of nitrogen promotes the clustering of diamond-like sites at the expense of graphitic ones leading to the decrease of the disorder. The film surface becomes rough with increasing nitrogen concentration. Films are optically transparent in the 200-900 nm wavelength range with a wide gap varying between 3.59 and 3.63 eV. There is an increase in resistivity from 15 to 87.4 x10-3Ω.cm for a-CNx thin films for 0.1< RF < 0.8 and a less decrease for RF > 0.8. Pore size increases in the films, but has little influence on band gaps. On the other hand, increasing the pore size reduces electrical interaction between particles by increasing resistivity.
Revathi Baskaran, Perumal Perumal, Deivamani Deivanayagam,
Volume 20, Issue 2 (6-2023)
Abstract
In this research, praseodymium (Pr) doped titanium oxide was deposited onto a glass substrate by nebulizer spray pyrolysis technique. The rare earth-doped thin film was subjected to studies on structural, morphological, optical, and gas sensing properties. The structural properties of the deposited thin films exhibit varied texture along with (101) direction. The grain size of the thin film varies with various mole percentages of doped TiO2 thin films. As various doping concentrations increase, the prepared thin films show different optical properties like band gap, extension coefficient, refractive index, and dielectric constant. Fourier transform infrared (FTIR) results revealed that the reflectance spectra conformed to the existence of functional groups and chemical bonding. Gas sensing studies were carried out for undoped and Pr-doped TiO2 films. The sensor was exposed to ethanol gas. The response of a TiO2 thin film at different ethanol concentrations and different operation temperatures was studied. The gas sensitivity of ethanol gas was measured when the fast response of the film with 0.004M Pr-doped TiO2 thin film showed a response time of 99 s and recovery time of 41 s, as well as the resistance falling to 0.6x106Ω. The sensor operated at maximum effectiveness at an optimum temperature of 200°C.
Y C Goswami,
Volume 21, Issue 0 (3-2024)
Abstract
CuS nanoparticles (NPs) with dimensions in the nanometer range were synthesized using a wet chemical approach. The comprehensive characterization of these NPs involved an analysis of their structure, composition, and optical properties, primarily conducted through X-ray diffraction (XRD) analysis. The XRD pattern conclusively confirmed the presence of the hexagonal phase in the CuS particles, a result corroborated by the accompanying Raman spectrum. The investigation further determined an estimated bandgap energy of 2.05 eV for the slightly sulfur-rich CuS NPs. Notably, this energy value exceeds that of bulk CuS (1.85 eV), indicating a noticeable miniaturization effect. The novel CuS NPs exhibited outstanding photocatalytic activity in the degradation of methyl Red (MR), particularly under visible light. This impressive performance is attributed to surface-bound OH ions on the CuS nanostructures, facilitating the adsorption and acceleration of the degradation process for MR molecules under visible light irradiation. The research presented in this article highlights the significant promise and efficiency of the synthesized CuS NPs as photocatalysts. These nanoparticles are particularly responsive to stable visible light, making them highly suitable for purifying chemically contaminated wastewater. Specifically, their effectiveness in degrading stable azo dyes, exemplified by MR, underscores their potential in practical applications.
Samrat Mane,
Volume 21, Issue 1 (3-2024)
Abstract
In this research work, Cadmium Sulphide thin film deposited on to glass substrate in a non-aqueous medium at 80 °C. The various physical preparative parameters and the deposition conditions, such as the deposition time and temperature, concentrations of the chemical species, pH, speed of mechanical stirring, etc., were optimized to yield good quality films. The as-prepared sample is tightly adherent to the substrate's support, less smooth, diffusely reflecting and was analyzed for composition. The synthesized film is characterized using X- ray diffraction (XRD), electrical and optical properties. It appears that the composites are rich in Cd. The grown CdS thin film had an orange-red color. A band gap of CdS thin film is 2.41 eV. The average crystallite size of the CdS film was 21.50 nm. The resistivity of the CdS thin film is about 5.212 x 105 W cm.
Umadevi Prasanna, Vijaya Kumar Kambila, Krishna Jyothi Nadella,
Volume 21, Issue 4 (12-2024)
Abstract
The composite solid polymer electrolyte films were prepared by doping nano-sized Fe2O3 particles on PVB (Polyvinyl Butyral) complexed with NaNO3 salt by solution casting technique. FTIR, XRD, and SEM methods characterized these electrolyte films. The Fourier Transform Infrared Spectroscopy and X-ray diffraction methods reveal the structural and complexation changes occurring in the electrolytes. The surface morphology of the electrolyte film was examined using the SEM (Scanning Electron Microscope) technique. The PVB+NaNO3+Fe2O3(70:30:3%) electrolyte shows a moderate ionic conductivity of 2.51×10−5 S cm−1 at ambient temperature (303 K). AC impedance spectroscopic analysis evaluates the ionic conductivity of the produced polymer electrolyte. Wagner's polarisation technique was applied to study the charge transport characteristics in the electrolyte films. The investigation revealed that ions constituted the majority of the transport carriers. An Open Circuit Voltage (OCV) of 2.0V and a Short Circuit Current (SCC) of 0.8 mA were found in the discharge characteristics data for the cell constructed with the polymer electrolyte sample.
Maryam Hajiebrahimi, Sanaz Alamdari, Omid Mirzaee,
Volume 21, Issue 4 (12-2024)
Abstract
Dual nanocomposites based on metal sulfide nanomaterials with a narrow band gap are favorable candidates for future optoelectronic applications and ionizing ray sensors. In this study, novel silver-doped zinc sulfide/ cadmium sulfide (ZnS/CdS: Ag) nanocomposites were synthesized using the cost-effective solvothermal approach. For the first time, the radiation sensitivity of the newly developed nanocomposite was assessed using a 241Am alpha source and ion beam-induced luminescence (IBIL) measurements. The ZnS/CdS: Ag nanocomposite demonstrated significant light emission in the blue-green spectrum when measured at room temperature. When exposed to alpha irradiation, the ZnS/CdS: Ag nanocomposite film displayed exceptional sensitivity compared to pure ZnS or CdS films. The FESEM images revealed a uniform distribution of semi-spherical and rod-shaped nanoparticles, with an average particle size measuring 180 nm. The results from XRD and EDX demonstrated distinct peaks corresponding to ZnS, CdS, and associated elements within the nanocomposite. The existence of several groups within the nanocomposite was confirmed through Fourier transform infrared spectroscopy. Evaluations revealed that the optical quality of the ZnS/CdS: Ag nanocomposite showed enhancement in comparison to pure ZnS and CdS. The results suggest that the ZnS/CdS: Ag nanocomposite film holds great promise for applications in optoelectronic devices and detection technologies.
