Search published articles

Showing 11 results for Nonlinear Analysis

Kheyr Aldin A., Mortezaei A.r.,
Volume 2, Issue 1 (3-2004)

Structural walls are used extensively in moderate- and high-rise buildings to resist lateral loads induced by earthquakes. The seismic performance of many buildings is, therefore, closely linked to the behavior of the reinforced concrete walls. The analytical models used in this paper are developed to study the push-over response of T-shaped reinforced concrete walls andinvestigate the influence of the flange walls on laterally loaded walls and nonlinear behavior of shear walls, namely strength, ductility and failure mechanisms. A layered nonlinear finite element method is used to study the behavior of T-shaped and rectangular (barbell) shear walls. This paper introduces a computer program to practically study three-dimensional characteristics of reinforced concrete wall response by utilizing layered modeling. The program is first verified bysimulated and reported experimental response of 3-D reinforced concrete shear walls. Subsequently, a study considering eighteen analytical test specimens of T-shaped and barbell shear walls is carried out. Finally, based on analytical results, a new equation for minimum ratio of shear wall area to floor-plan area is proposed.
F. R. Rofooei, N. K. Attari, A. Rasekh, A.h. Shodja,
Volume 4, Issue 3 (9-2006)

Pushover analysis is a simplified nonlinear analysis technique that can be used to estimate the dynamic demands imposed on a structure under earthquake excitations. One of the first steps taken in this approximate solution is to assess the maximum roof displacement, known as target displacement, using the base shear versus roof displacement diagram. That could be done by the so-called dynamic pushover analysis, i.e. a dynamic time history analysis of an equivalent single degree of freedom model of the original system, as well as other available approximate static methods. In this paper, a number of load patterns, including a new approach, are considered to construct the related pushover curves. In a so-called dynamic pushover analysis, the bi-linear and tri-linear approximations of these pushover curves were used to assess the target displacements by performing dynamic nonlinear time history analyses. The results obtained for five different special moment resisting steel frames, using five earthquake records were compared with those resulted from the time history analysis of the original system. It is shown that the dynamic pushover analysis approach, specially, with the tri-linear approximation of the pushover curves, proves to have a better accuracy in assessing the target displacements. On the other hand, when nonlinear static procedure seems adequate, no specific preference is observed in using more complicated static procedures (proposed by codes) compared to the simple first mode target displacement assessment.
Ali Kheyroddin, Hosein Naderpour,
Volume 5, Issue 1 (3-2007)

A parametric study is performed to assess the influence of the tension reinforcement index, ( ω = ρ fy /f Bc), and the bending moment distribution (loading type) on the ultimate deformation characteristics of reinforced concrete (RC) beams. The analytical results for 15 simply supported beams with different amounts of tension reinforcement ratio under three different loading conditions are presented and compared with the predictions of the various formulations and the experimental data, where available. The plastic hinge rotation capacity increases as the loading is changed from the concentrated load at the middle to the third-point loading, and it is a maximum for the case of the uniformly distributed load. The effect of the loading type on the plastic rotation capacity of the heavily reinforced beams is not as significant as that for the lightly reinforced beams. Based on the analytical results obtained using the nonlinear finite element method, new simple equations as a function of the tension reinforcement index, ω, and the loading type are proposed. The analytical results indicate that the proposed equations can be used for analysis of ultimate capacity and the associated deformations of RC beams with sufficient accuracy.
Alireza Mortezaei, Ali Kheyroddin,
Volume 7, Issue 1 (3-2009)

The work presented in this paper investigates the causes of size effects in structural-concrete members. It is

based on the use of a finite-element model found to yield realistic predictions of structural-concrete behavior in all

cases investigated to date. In fact, the previous use of this model in investigations of size effects in reinforced-concrete

beams indicated that such effects reflect the dependence of load-carrying capacity on small unintended eccentricities

of the applied load and/or load-induced anisotropy, rather than, as widely considered, on fracture-mechanics

characteristics. The present work extends the scope of the above investigation so as to include the case of reinforced

concrete flanged shear walls, the behavior of which is already established experimentally. It is found that, unlike the

flanged shear walls with a height-to-length ratio larger than 2, the shear walls investigated in the present work, in

contrast with the interpretation given to recently published experimental findings, are size-effect independent.

R. Attarnejad, F. Kalateh,
Volume 10, Issue 1 (3-2012)

This paper describes a numerical model and its finite element implementation that used to compute the cavitation effects on

seismic behavior of concrete dam and reservoir systems. The system is composed of two sub-systems, namely, the reservoir and

the dam. The water is considered as bilinear compressible and inviscid and the equation of motion of fluid domain is expressed

in terms of the pressure variable alone. A bilinear state equation is used to model the pressure–density relationship of a cavitated

fluid. A standard displacement finite element formulation is used for the structure. The Structural damping of the dam material

and the radiation damping of the water and damping from foundation soil and banks have been incorporated in the analysis. The

solution of the coupled system is accomplished by solving the two sub-systems separately with the interaction effects at the damreservoir

interface enforced by a developed iterative scheme. The developed method is validated by testing it against problem for

which, there is existing solution and the effects of cavitation on dynamic response of Konya gravity dam and Morrow Point arch

dam subjected to the first 6 s of the May 1940 El-Centro, California earthquake, is considered. Obtained results show that impact

forces caused by cavitation have a small effect on the dynamic response of dam-reservoir system.

L. Kalani Sarokolayi, B. Navayi Neya, Javad Vaseghi Amiri,
Volume 13, Issue 1 (3-2015)

This study focuses on non-linear seismic response of a concrete gravity dam subjected to translational and rotational correlated components of ground motions including dam-reservoir interaction. For this purpose rotational components of ground motion is generated using Hong Non Lee improved method based on corresponding available translational components. The 2D seismic behavior of the dam concrete is taken into account using nonlinear fracture mechanics based on the smeared- crack concepts and the dam-reservoir system are modeled using Lagrangian-Lagrangian approach in finite element method. Based on presented formulation, Pine Flat concrete gravity dam is analyzed for different cases and results show that the rotational component of ground motion can increase or decrease the maximum horizontal and vertical displacements of dam crest. These results are dependent on the frequency of dam-reservoir system and predominant frequencies of translational and rotational components of ground motion.
A. Fooladi, Mo.r. Banan,
Volume 13, Issue 2 (6-2015)

Latticed columns are frequently used in industrial steel structures. In some countries these built-up columns might be even used in other types of steel structures such as residential and commercial buildings. Besides, latticed columns are parts of skeletons of many historic buildings all around the world. To analyze a steel structure with latticed columns a more accurate numerical model for such a column seems to be essential. The lay-out and connectivity of constructing main profiles of a latticed column leads to formation of many shear zones along the length of a column. Therefore, considering shear effects on the behavior of a lattice column is inevitable. This paper proposed a new super-element with twelve degrees of freedom to be used in finite element modeling of latticed columns. The cross sectional area, moments of inertia, shear coefficient and torsional rigidity of the developed new element are derived. To compute these parameters with less complexity a model using only beam elements is also introduced. A general purpose finite element program named LaCE is developed. This FE program is capable of performing linear and nonlinear analysis of 3D-frames with latticed columns, considering shear deformation. To show the accuracy of the proposed element, several cases are studied. The outcome of these investigations revealed that the current-in-practice model for latticed columns suffers from some major shortcomings which to some extends are resolved by the proposed super-element. The developed element showed the capability of modeling a lattice column with good accuracy and less computational cost.
Mohsen Gerami, Ali Kheyroddin, Abbas Sivandi-Pour,
Volume 14, Issue 1 (1-2016)

Steel-concrete hybrid systems are used in buildings, in which a steel structure has been placed on a concrete structure to make a lighter structure and have a faster construction. Dynamic analysis of hybrid structures is usually a complex procedure due to various dynamic characteristics of each part, i.e. stiffness, mass and especially damping. Dynamic response of hybrid structures has some complications. One of the reasons is the different stiffness of the two parts of structure and another reason is non-uniform distribution of materials and their different features such as damping in main modes of vibration. The available software is not able to calculate damping matrices and analyze these structures because the damping matrix of these irregular structures is non-classical. Also an equivalent damping should be devoted to the whole structure and using the available software. In the hybrid structures, one or more transitional stories are used for better transition of lateral and gravity forces. In this study, an equation has been proposed to determining the equivalent uniform damping ratio for hybrid steel-concrete buildings with transitional storey(s). In the proposed method, hybrid buildings are considered to have three structural systems, reinforced concrete, transitional storey and steel. Equivalent uniform damping ratio is derived by means of a semi-empirical error minimization procedure.

Alireza Habibi, Ehsan Jami,
Volume 15, Issue 2 (3-2017)

The seismic performance levels are discrete damage states selected from among the infinite spectrum of possible damage states that buildings could experience as a result of earthquake response. The observation of building damage during strong motion earthquakes showed that correlation of structural damage with a single parameter such as peak ground acceleration or the total seismic duration is low while peak ground acceleration is often used as a main seismic parameter to evaluate seismic performance of structures. Main objective of this study is to determine the relationship between several seismic acceleration parameters and the Target Displacement (TD) of steel frame structures, which is an important parameter to identify performance levels. For this purpose, first, nonlinear analysis is performed on the SAC 3- and 9-story frames subjected to several far-field earthquakes and then target displacements and seismic parameters are calculated for each structure.The relationship between the target displacement and seismic parameters is evaluated in the form of correlation coefficient. It is shown that PGA has poor correlation with the target displacement. On the other hand, HOUSNER intensity, spectral pseudo-acceleration, spectral pseudo-velocity and peak ground velocity exhibit strong correlation with TD.

Muhammad Yousaf, Zahid Ahmed Siddiqi, Muhammad Burhan Sharif, Asad Ullah Qazi,
Volume 15, Issue 4 (6-2017)

In this study, a comparison is made between force and displacement controlled non-linear FE analyses for an RC beam in flexure with partially developed steel bars. An FE model with slightly unsymmetrical reinforcement was analyzed by applying two-point loading using both force and displacement controlled methods. The responses obtained using ANSYS-13 were validated against available experimental data. Combined comparative display of flexural response of the beam using force and displacement controlled analysis, that has least been addressed in the literature, is given here. Study choses large-deformation-nonlinear plastic analysis scheme, discrete modeling approach for material modeling and program-chosen incremental scheme following Newton-Raphson method. The results show that displacement controlled approach is efficient in terms of time saving and less disk space requirement along with the ability to give falling branch of load-deflection response, if element displacement capacity still exists. Moreover, it gives an early estimate of the load carrying capacity of the structural element along with suitable values of convergence and non-linear solution parameters. However, for a beam with unsymmetrical detailing, force controlled analysis method seems to yield more realistic and practical results in terms of mid span deflection and beam cracking behavior compared with assumed symmetric displacement controlled technique. It also gives true fracture prediction at ultimate load level, which is not true for the displacement controlled method as the computer code forces the model to maintain equal displacements at two load points, falsely increasing the capacity of the beam.

Xiaolei Chen, Jianping Fu, Feng Xue, Xiaofeng Wang,
Volume 15, Issue 4 (6-2017)

This paper presents a comparative numerical research on the overall seismic behavior of RC frames with different types of rebars (normal versus high strength rebar). A nonlinear numerical model is developed and is validated using experimental results. Comparing the numerical and experimental behaviors shows that the developed model is capable of describing the hysteretic behavior and plastic hinges development of the experimental RC frames with various strength longitudinal steel bars. The validated model is then used, considering the influences of axial load ratios and volumetric ratios of longitudinal rebars of column, to investigate the effects of reinforcement strength on the overall seismic behavior of RC frames. The simulation results indicate that utilizing high strength reinforcement can improve the structural resilience, reduce residual deformation and achieve favorable distribution pattern of plastic hinges on beams and columns. The frames reinforced with normal and high strength steel bars have comparable overall deformation capacity. The effect of axial load ratio on the energy dissipation, hysteretic curves and ultimate lateral load of frames with different strength rebars is similar. In addition, increasing the volumetric ratios of longitudinal rebars can increase the ultimate lateral load of frame and improve the plastic hinge distribution of frame.

Page 1 from 1     

© 2024 CC BY-NC 4.0 | International Journal of Civil Engineering

Designed & Developed by : Yektaweb