Search published articles


Showing 5 results for Direct Shear Test

A. Hamidi, M. Alizadeh, S.m. Soleimani,
Volume 7, Issue 1 (3-2009)
Abstract

There are limitations in experimental studies on sand-gravel mixtures due to the small size of testing

specimens. Due to this problem, many researchers have worked on prediction of the shear strength of mixture by testing

the sandy fraction of soil alone and developed empirical relationships. Most of the previous relationships have been

determined for low surcharge pressures in which particle breakage does not affect the shear strength parameters.

However, the particle breakage affects the relationships in higher confinements. At the present study, the results of

large scale direct shear tests on sand and sand-gravel mixtures was used to investigate the shear behavior and

dilatancy characteristics in a wider range of surcharge pressures. The gravel content, relative density, surcharge

pressure and gravel grain size were considered as variables in testing program. The relationships between shear

strength characteristics of sand and sand-gravel mixtures were determined considering dilation characteristics of the

soil. In this regard, the minimum void ratio was found as a useful indirect index that relates uniquely to the critical

state friction angle independent of soil gradation. The relations between critical state or peak friction angles of the

mixture with minimum void ratio were determined as a function of surcharge pressure. The correlations could be useful

for determination of the strength parameters of sand-gravel composites by testing sandy fraction of mixture.


M.r. Abdi, S. A. Sadrnejad, M.a. Arjomand,
Volume 7, Issue 4 (12-2009)
Abstract

Large size direct shear tests (i.e.300 x 300mm) were conducted to investigate the interaction between clay reinforced with geogrids embedded in thin layers of sand. Test results for the clay, sand, clay-sand, clay-geogrid, sandgeogrid and clay-sand-geogrid are discussed. Thin layers of sand including 4, 6, 8, 10, 12 and 14mm were used to increase the interaction between the clay and the geogrids. Effects of sand layer thickness, normal pressure and transverse geogrid members were studied. All tests were conducted on saturated clay under unconsolidated-undrained (UU) conditions. Test results indicate that provision of thin layers of high strength sand on both sides of the geogrid is very effective in improving the strength and deformation behaviour of reinforced clay under UU loading conditions. Using geogrids embedded in thin layers of sand not only can improve performance of clay backfills but also it can provide drainage paths preventing pore water pressure generations. For the soil, geogrid and the normal pressures used, an optimum sand layer thickness of 10mm was determined which proved to be independent of the magnitude of the normal pressure used. Effect of sand layers combined with the geogrid reinforcement increased with increase in normal pressures. The improvement was more pronounced at higher normal pressures. Total shear resistance provided by the geogrids with transverse members removed was approximately 10% lower than shear resistance of geogrids with transverse members.
M. Karimpour Fard, N. Shariatmadari, M. Keramati, H. Jafari Kalarijani,
Volume 12, Issue 4 (12-2014)
Abstract

Due to the existence of fibrous materials such as plastic fragments, the strength anisotropy of Municipal Solid Waste

(MSW) materials is the main source of differences between their mechanical response in direct shear and triaxial apparatus.

As an extension of earlier research on the mechanical behavior of MSW using a large traixail apparatus, results presented in

Shariatmadari et al. [1] and Karimpour-Fard et al. [2], the current study was programmed and executed. MSW samples were

tested using a computer controlled large shear box apparatus with normal stress levels ranging between 20 to 200 kPa. The

effect of fiber content, fiber orientation, aging and shearing rate on the response of MSW were addressed. The results showed

that shear strength of MSW increases with normal stress, although, in spite of the presence of reinforcement elements in MSW

and unlike the results from triaxial tests, no strain hardening could be observed in their mechanical response. An increase in

the shear strength of MSW was observed with increasing the shearing rate. Increasing the shearing rate from 0.8 to 19

mm/min, enhanced the shear strength of samples from 16 to 27% depending on the shear displacement level. Although, the

same trend was investigated in traixial tests, but lower rate-sensitivity in the mechanical response of MSW in direct shear tests

were observed.

Unlike the results of triaxial tests with aging process, mobilized shear strength level of MSW samples tested under direct

shearing decreased comparing fresh samples. It was also observed that altering the fiber content and their orientation could

affect the mechanical response and shear strength of the MSW. Additionally, there is an optimum fiber angle in MSW which

yields the highest level of shearing strength.


Omar Al Hattamleh,
Volume 14, Issue 2 (3-2016)
Abstract

ABSTRACT The influence of the sand placement method above geotextile layer on interface shear strength behavior was investigated. Seven different types of woven and non woven geotextile were used with only poorly graded sand. The investigation involved placement of sand layer through inclined horizontal plane with different angles. This step constitutes a fundamental step for assessing soil to be deposited in different plane and therefore with different internal soil fabric. The interface shear strength was evaluated by using direct shear test. Although the investigated soil is uniform poorly graded sand, the influence of the deposit plane was significant especially for nonwoven geotextile. Differences in soil interface shear strength associated with the tested geotextiles samples shows that samples with higher mass per unit area and same opening sizes had the higher interface friction angle regardless the bedding plane. Influence of bedding plane on interface modulus of elasticity which used in most of interface modeling was investigated using Janbu’s formula. It is noted that the use of secant interface modulus of elasticity at 1% strain and at 50% of peak stresses gave a consistent prediction of n and Ku constant appear in Janbu’s formula for all types of geotextile. The above results were reflected in the prediction for interface molded such as Chen and Juran as shown. Therefore, the existing interface modeled is needed to be modified to account for the method that the sand is being placed above the geotextile layer.



Volume 15, Issue 6 (9-2017)
Abstract

Pile load tests and numerical analysis of a small-scale model pile in unsaturated clayey soil are presented in this paper. A small-scale model pile was simulated to bear a static axial loading in unsaturated soil using finite element method. All parameters used in the finite element method were obtained in laboratory tests, including the direct shear test, interface direct shear test, and filter paper method. The numerical analysis results were compared with the pile load test results. The results show that the general trend of pile load and pile head settlement relationship obtained by the numerical analysis shows a good consistence with the pile load test results. With increasing water content of the soil, the matric suction, dilatancy angle and shear strength decrease, and consequently the ultimate bearing capacity of pile decreases.



Page 1 from 1     

© 2021 CC BY-NC 4.0 | International Journal of Civil Engineering

Designed & Developed by : Yektaweb