Search published articles


Showing 55 results for Strength

Omar Al Hattamleh,
Volume 14, Issue 2 (3-2016)
Abstract

ABSTRACT The influence of the sand placement method above geotextile layer on interface shear strength behavior was investigated. Seven different types of woven and non woven geotextile were used with only poorly graded sand. The investigation involved placement of sand layer through inclined horizontal plane with different angles. This step constitutes a fundamental step for assessing soil to be deposited in different plane and therefore with different internal soil fabric. The interface shear strength was evaluated by using direct shear test. Although the investigated soil is uniform poorly graded sand, the influence of the deposit plane was significant especially for nonwoven geotextile. Differences in soil interface shear strength associated with the tested geotextiles samples shows that samples with higher mass per unit area and same opening sizes had the higher interface friction angle regardless the bedding plane. Influence of bedding plane on interface modulus of elasticity which used in most of interface modeling was investigated using Janbu’s formula. It is noted that the use of secant interface modulus of elasticity at 1% strain and at 50% of peak stresses gave a consistent prediction of n and Ku constant appear in Janbu’s formula for all types of geotextile. The above results were reflected in the prediction for interface molded such as Chen and Juran as shown. Therefore, the existing interface modeled is needed to be modified to account for the method that the sand is being placed above the geotextile layer.


Guray Arslan, Muzaffer Borekci, Muzaffer Balci, Melih Hacisalihoglu,
Volume 14, Issue 3 (4-2016)
Abstract

The contribution of concrete to inelastic deformation capacity and shear strength of reinforced concrete (RC) columns failing in shear has been investigated extensively by various researchers. Although RC members are designed to have shear strengths much greater than their flexural strengths to ensure flexural failure according to the current codes, shear degradation of RC columns failing in flexure has not been studied widely. The aim of this study is to investigate the shear degradation of RC columns using finite element analyses (FEA). The results of FEA are compared with the results of experimental studies selected from literature, and it is observed that the lateral load-deflection curves of analysed columns are compatible with the experimental results. Twenty-six RC columns were analysed under monotonically increasing loads to determine the concrete contribution to shear strength. The results of analyses indicate that increasing the ratio of shear to flexural strength reduces the concrete contribution to shear strength of the columns.


Mahmood Reza Abdi, Hamed Mirzaeifar,
Volume 14, Issue 4 (6-2016)
Abstract

Abstract To meet construction demands, reinforcement and stabilization methods have been widely used to improve properties and mechanical behavior of clays. Although cement stabilization increases soil strength, at the same time reduces ductility which is of paramount importance in roads, landfill covers, etc. In current study, kaolinite was stabilized with 1, 3 and 5% cement and mixed with 0.05, 0.15, 0.25 and 0.35% polypropylene fibers to increase ductility. Samples were cured at 35°C for 1, 7 and 28 days and subjected to unconfined compression tests. Results showed that inclusion of discrete fibers to uncemented and cemented kaolinite reduced stiffness and the loss of post-peak strength and changed brittle behavior of cemented samples to a more ductile behavior. Cement and fiber contents as well as curing period were found to be the most influential factors and fiber – soil interaction was influenced by binding materials.


Hynn-Ki Choi,
Volume 14, Issue 6 (9-2016)
Abstract

Replacement of existing unreinforced masonry (URM) walls, commonly used as a non-structural member in apartments, with new reinforced concrete (RC) components has been used as a reliable method when remodeling is carried out. However, special care needs to be taken when URM walls are removed not to waste construction time and materials. Therefore, retrofitting existing URM walls can be deemed a better solution rather than replacing URM walls with RC ones. Using shotcrete is one of retrofitting techniques of URM walls. However, using normal shotcrete cannot improve adequate ductility and may cause brittle failure at a wall-frame or slab connection. Therefore, new materials such as engineered cementitious composite (ECC) and ultra-high performance concrete (UHPC) have emerged to resolve the problem of normal shotcrete by increasing ductility and toughness of retrofitting materials. In this study, sprayed ECC was used to increase both strength and ductility of existing URM walls. The results of two retrofitted URM walls under lateral quasi-static loading were compared to non-retrofitted one. One strengthened wall, retrofitted masonry wall (RTM)-ECC, was just sprayed and anchored to a wall base. Another strengthened wall, RTM-ECC-WM, was the same as RTM-ECC except for addition of wire mesh. The retrofitted specimens showed significant increase of strength, ductility, and energy dissipation capacity in comparison with the control one. In addition, RTM-ECC-WM indicated better strength degradation due to the load transferring effect of wire mesh than RTM-ECC.


Hossein Soltani-Jigheh,
Volume 14, Issue 7 (10-2016)
Abstract

The main objective of present study is to possible use of plastic waste materials for reinforcing clayey soils. An experimental study was planned to investigate compressibility and undrained shear behavior of clayey soil mixed with plastic waste. The mixtures were prepared with various amount of plastic waste (i.e. 0%, 0. 5%, 1.0%, 1.5% and 3.0% in dry weight) and interactive effect of plastic waste, plastic flexibility, confining pressure and initial density on the behavior of clayey soil was studied by performing compaction, consolidated undrained triaxial and oedometer consolidation test. The results show that plastic wastes do not affect compaction characteristics of clayey soil considerably and adding them to the clay more than a specific value (i.e. 1.0% in this research) causes to change undrained behavior of samples from contractive to dilative. In addition, beyond this specific value, it improves shear strength and reduces compressibility of clay. The rate of increase in shear strength and decrease in compressibility depends on the confining pressure, flexibility of plastic and initial density of samples. It is more noticeable when plastic waste in mixtures is relatively rigid and density and confining pressure are high. Moreover, plastic waste has a negative effect on the free swelling, swelling pressure and swelling index of samples, so that these parameters for plastic waste mixed clay are higher than the associated values of plain clay.


Saeid Sabouri-Ghomi, Barash Payandehjoo,
Volume 15, Issue 1 (1-2017)
Abstract

Abstract The Drawer Bracing System (DBS) is a ductile bracing system that is developed to enhance the seismic performance of braced frames. The system is composed of three parallel plates that are attached together via transfer plates at right angle. Seismic energy is dissipated through the formation of flexural plastic hinges at the two ends of the transfer plates. The parallel plates must have adequate strength and stiffness to prevent global buckling and to remain elastic while transferring forces to transfer plates. Height, width, thickness and the number of the transfer plates may be varied to achieve the desired strength and stiffness of the system. In contrast to common bracing systems, the main advantage of a DBS is the conversion of the axial forces to flexural moments in the dissipating elements. In the present paper, the nonlinear shear response of the DBS is predicted via closed-form formulas for calculation of strength, stiffness and post-yield behavior of the system. These formulations are based on both experimental observations and theoretical analysis. The calculated force-displacement backbone curve is verified to be a very good approximation for predicting the nonlinear shear response of the system.


Masoud Ahmadi , Hosein Naderpour , Ali Kheyroddin ,
Volume 15, Issue 2 (3-2017)
Abstract

Concrete filled steel tube is constructed using various tube shapes to obtain most efficient properties of concrete core and steel tube. The compressive strength of concrete is considerably increased by the lateral confined steel tube in circular concrete filled steel tube (CCFT). The aim of this study was to present an integrated approach for predicting the steel-confined compressive strength of concrete in CCFT columns under axial loading based on large number of experimental data using artificial neural networks. Neural networks process information in a similar way the human brain does. Neural networks learn by example. The main parameters investigated in this study include the compressive strength of unconfined concrete (f'c), outer diameter (D) and length (L) of column, wall thickness (t) and tensile yield stress (fy) of steel tube. Subsequently, using the reliable network, empirical equations are developed for the confinement effect. The results of proposed model are compared with recently existing model on the basis of the experimental results. The findings demonstrate the precision and applicability of the empirical approach to determine capacity of CCFT columns.


Mustafa Sarıdemir, Serhat__celikten@hotmail.com Metin Hakan Severcan, Murat Çiflikli, Serhat Çelikten,
Volume 15, Issue 2 (3-2017)
Abstract

In this study, the effects of high temperatures on the mechanical and microstructural properties of high strength concretes (HSCs) made with metakaolin (MK) are investigated. For this purpose, the concrete mixtures made with MK were produced with water-binder ratio of 0.2. The mechanical properties of these concretes at 25, 250, 500 and 750 oC temperatures were determined. Besides, the effect of high temperature on the microstructural changes of cementitious matrix, interfaces between aggregate particles-cementitious materials and aggregates of these concretes were inspected by X-ray diffraction, scanning electron microscope and plane polarized transmitted light (PPTL) analyses. The results indicate that the ultrasound pulse velocity, compressive strength, flexural strength and splitting tensile strength values of these concretes decrease especially depending on the increase of the high temperature after 250 oC. The heated concrete specimens were also examined at both macro and micro scales to determine the discoloration, alteration and cracks of HSC at different temperatures. PPTL analyses show that increasing temperature cause impairing of interfaces between aggregate particles and cementitious materials. The results also show that the partial replacement of MK with cement has the best performance on the mechanical properties of HSC.


Suresh Prasad Singh, Meena Murmu,
Volume 15, Issue 4 (6-2017)
Abstract

This paper outlines the effects of curing conditions on the strength and hydration products of lime activated slag cement. The slag cement was prepared by activating the ground granulated blast furnace slag with lime and plaster of Paris. The curing of mortar specimens was done at temperatures of 270, 450,600,750C and the compressive strength of specimens were determined after curing periods of 3,7, 28, 56 and 90days. The curing temperature is found to influence both the early and later age strengths. For the present test conditions the highest 90days compressive strength was found to be 47.63MPa for the specimen cured at temperature of 600C. Further, the developed strength in mortar specimens were correlated with the hydration products and microstructure using X-ray diffraction and scanning electron microscope results. Generalized reduced gradient technique is adopted to find the optimum curing temperature for the given raw material composition and this is found to vary marginally on curing period. 



Volume 15, Issue 4 (6-2017)
Abstract

THIS IS THE REVISED VERSION OF THE PAPER A-10-581-3, CONSIDERED AS "MAJOR REVISION": One of the best methods to improve structural seismic behavior is to strengthen the infills by shotcreting. Most rehabilitation codes have a special part for masonry buildings and masonry infill panels. However they are completely silent for infills improved by concrete covers, probably for the lack of sufficient experimental test data. This paper focuses on the ultimate strength and modification factor of this type of infill panels, based on some experimental studies. The proposed formula of the existing codes for the equivalent width of the masonry infill panels is improved for the ultimate strength of shotcreted infill panels. It is also shown that the modification factors of the masonry and clay tile infill panels are downgraded and upgraded, respectively, if they are rehabilitated by concrete covers. The envelopes of the load-displacement behavior of the specimens are applied to calculate the modification factor, rather than the standard back bone curves. It is shown that they give more conservative values for the m-factor. Subsequently, some suggestions are proposed to estimate m-factor of shotcreted infill panels.



Volume 15, Issue 4 (6-2017)
Abstract

Bridges normally undergo nonlinear deformations during a near field strong ground motion resulting in a critical deviation of their columns from the plumb state due to considerable residual deformations. These excessive residual deformations make a bridge, which has not collapsed, ‘irreparable’ and in turn ‘not operable.’ Therefore, reasonable prediction of these types of bridge piers deformations is of great importance in order to evaluate the serviceability of bridges subjected to a seismic scenario. Conventional hysteresis models formulated for typical concrete columns are normally used for this purpose which most of times fail to correctly predict the residual deformations occurred as a result of a one-sided or directivity pulse excitation. The present research aims at development of a peak oriented hysteresis model being able to regenerate residual deformations more reasonable compared to the conventional hysteresis models. This multi linear peak oriented model considers strength deterioration in each half cycle in addition to stiffness degradations in unloading cycles. Yielding points differ in both positive and negative sides of the hysteresis model that enables us to define a different elastic stiffness of both sides in asymmetric concrete sections. Another remarkable property of this model is breaking points and strength deterioration in unloading and reloading stages. This work also compares the obtained results to the conventional hysteresis models, namely bilinear, Clough, Q-Hyst, Takeda and Bouc-Wen in terms of prediction of residual nonlinear deformations in cyclic or dynamic analysis of reinforced concrete single-column bridge piers. The obtained results prove higher relative accuracy of the proposed model.


Muhammad Yousaf, Zahid Ahmed Siddiqi, Muhammad Burhan Sharif, Asad Ullah Qazi,
Volume 15, Issue 4 (6-2017)
Abstract

In this study, a comparison is made between force and displacement controlled non-linear FE analyses for an RC beam in flexure with partially developed steel bars. An FE model with slightly unsymmetrical reinforcement was analyzed by applying two-point loading using both force and displacement controlled methods. The responses obtained using ANSYS-13 were validated against available experimental data. Combined comparative display of flexural response of the beam using force and displacement controlled analysis, that has least been addressed in the literature, is given here. Study choses large-deformation-nonlinear plastic analysis scheme, discrete modeling approach for material modeling and program-chosen incremental scheme following Newton-Raphson method. The results show that displacement controlled approach is efficient in terms of time saving and less disk space requirement along with the ability to give falling branch of load-deflection response, if element displacement capacity still exists. Moreover, it gives an early estimate of the load carrying capacity of the structural element along with suitable values of convergence and non-linear solution parameters. However, for a beam with unsymmetrical detailing, force controlled analysis method seems to yield more realistic and practical results in terms of mid span deflection and beam cracking behavior compared with assumed symmetric displacement controlled technique. It also gives true fracture prediction at ultimate load level, which is not true for the displacement controlled method as the computer code forces the model to maintain equal displacements at two load points, falsely increasing the capacity of the beam.


Artur Duchaczek, Zbigniew Mańko,
Volume 15, Issue 4 (6-2017)
Abstract

The paper is presented an attempt to assess service life of steel girders in military bridges (or by-pass temporary bridges) when fatigue cracks are detected in them. A function describing the geometry of fatigue cracks, the so-called crack shape factor Y, for two different, assumed calculated models, was presented. The function was used to plot sample graphs allowing assessing the remaining service life of such structural elements or engineering structures in a simple way. This method of analyzing can be used not only for the military bridges but also for other steel structures with existing cracks. The work is also presented assessments of possible applications of two FEM calculated models using shell elements to test stress and deformation at the top part of a fatigue crack located in a web of a steel girder used in the military bridges. The results of the conducted numerical analyses were compared with the results obtained in experimental research conducted in laboratory conditions using extensometers.


Xiaolei Chen, Jianping Fu, Feng Xue, Xiaofeng Wang,
Volume 15, Issue 4 (6-2017)
Abstract

This paper presents a comparative numerical research on the overall seismic behavior of RC frames with different types of rebars (normal versus high strength rebar). A nonlinear numerical model is developed and is validated using experimental results. Comparing the numerical and experimental behaviors shows that the developed model is capable of describing the hysteretic behavior and plastic hinges development of the experimental RC frames with various strength longitudinal steel bars. The validated model is then used, considering the influences of axial load ratios and volumetric ratios of longitudinal rebars of column, to investigate the effects of reinforcement strength on the overall seismic behavior of RC frames. The simulation results indicate that utilizing high strength reinforcement can improve the structural resilience, reduce residual deformation and achieve favorable distribution pattern of plastic hinges on beams and columns. The frames reinforced with normal and high strength steel bars have comparable overall deformation capacity. The effect of axial load ratio on the energy dissipation, hysteretic curves and ultimate lateral load of frames with different strength rebars is similar. In addition, increasing the volumetric ratios of longitudinal rebars can increase the ultimate lateral load of frame and improve the plastic hinge distribution of frame.


Ali Allahverdi, Mostafa Mahinroosta, Shima Pilehvar,
Volume 15, Issue 5 (7-2017)
Abstract

Compressive strength is as one of the most important properties of concrete and mortar that its measurement may be necessary at both early and later ages. Prediction of compressive strength by a proper model is a fast and cost-effective way for evaluating cement quality under various curing conditions. In this paper, a logarithmic model based on the results of an experimental work conducted to investigate the effects of curing time and temperature on the compressive strength development of chemically activated high phosphorous slag content cement has been presented. This model is in terms of curing time and temperature as independent variables and compressive strength as dependent variable. For this purpose, mortar specimens were prepared from 80 wt.% phosphorous slag, 14 wt.% Portland cement, and 6 wt.% compound chemical activator at Blaine fineness of 303 m2/kg. The specimens were cured in lime-saturated water under temperatures of 25, 45, 65, 85 and 100 ºC in oven. The model has two adjustable parameters for various curing times and temperatures. Modeling has been done by applying dimensionless insight. The proposed model can efficiently predict the compressive strength of this type of high phosphorous slag cement with an average relative error of less than 4%.



Page 3 from 3     

© 2024 CC BY-NC 4.0 | International Journal of Civil Engineering

Designed & Developed by : Yektaweb