---

Physical modeling for study of deep foundations can be performed in simple chambers (1g), calibration chambers (CC),

and centrifuge apparatus (ng). These common apparatus face certain limitations and difficulties. Recently, Frustum Confining

Vessels (FCV) have been evolved for physical modeling of deep foundations and penetrometers. Shaped as the frustum of a

cone, this device applies steady pressure on its bottom and creates a linear stress distribution along its vertical central core.

This paper presents the key findings in FCV, as developed in AUT. The FCV has a height of 1200 mm, with top and bottom

diameters of 300 and 1300 mm, respectively. By applying bottom pressure up to 600 kPa, the in-situ overburden stress

conditions, equivalent up to 40 m soil deposits, become consistent with the embedment depth of commonly used piles.

Observations indicated that a linear trend of stress distribution exists, and this device can create overburden stress in the

desired control volume along the central core. Moreover, a couple of compressive and tensile load tests were performed on

steel model piles driven in sand with a length of 750 mm, and different length to diameter (L/D) ratios between 8-15.

Comparison between measured and predicted ultimate capacity of model piles performed in FCV demonstrate a suitable

conformity for similar confinement conditions in the field. Therefore, the FCV can be considered as an appropriate approach

for the investigation of piling geotechnical behavior, and the examination of construction effects.

---

This research examines the behavior of soil-reinforced piles and applied loads based on the analytical method and by using the numerical results of FLAC3D software for comparison with the analytical results. The analysis was based on a method called virtual retaining wall, the following into consideration: an imaginary retaining wall that passes the footing edge the bearing capacity of footing on reinforced soil with piles, which was determined by applying equilibrium between active and passive forces on virtual wall and a pile row that exists beneath the shallow foundation. To calculate the lateral pile resistance here, an analytical equation was then required. The main objective of this paper is to determine the percentage of applied load on pile. Similarly, the effect of adding pile in various positions relative to the present footing (underpinning) was studied in this research. The various parameters of this study included pile length, vertical distance of pile head to shallow footing, pile distance to center of footing and location of the pile. Finally, the findings were compared with the numerical results of FLAC3D and the formerly presented experimental results. Results show that the analytical method, while being close to other methods is more conservative.

---

We report engineering experiences from the critical task of relief well installation under high artesian flow conditions at the downstream toe of the Karkheh earth dam, Iran. Due to the establishment of excessive uplift pressure at the downstream toe of the Karkheh dam, installation of a series of new relief wells was considered to permanently relieve part of these pressures. The mentioned uplift pressure, as high as around 30 m above the ground level, was produced in a confined conglomerate aquifer bounded above and below by relatively impervious mudstone layers which reduced the safety factor of the dam toe to below 1.0. Investigations on the shortcomings of the old relief wells installed at the dam site showed that the main problems were: insufficient well numbers, insufficient well diameters, irregular well screens causing their blockage by time passing, and insufficient total opening area. Despite engineering difficulties and associated risk of downstream toe instability, installation of new relief wells was successfully completed under high artesian flow conditions” was successfully completed. The employed technique for the construction of the new relief wells under flowing artesian conditions was based on: 1) cement grouting and casing of the well, 2) telescopic drilling, 3) application of appropriate drilling fluid, and 4) controlling the artesian flow by adding a long vertical pipe to the top of the relief wells. Numerical modeling of seepage for the Karkheh dam foundation showed that, as a result of the installation of the new relief wells, the safety factor of the downstream toe increased to the safe value of 1.3 for the normal reservoir water level.

---

The use of recycled bassanite, produced from gypsum wastes, in ground improvement projects is initiated recently in Japan to eliminate the huge quantities of gypsum wastes. Meanwhile the use of recycled bassanite has a positive effect on the environment and economy, it has many challenges. These challenges are related to the release of fluorine more than the standard limits results in contaminated fluorine soil. This research investigates the effect of the amount of bassanite, and water content on the release of fluorine from MC-clay soil stabilized with bassanite, taking in consideration their effect on the compressive strength. Recycled bassanite was mixed with furnace cement with a ratio of 1:1 to prevent the solubility of bassanite. Different amounts of this admixture were mixed with the tested soil at different water contents. Unconfined compression test was used to determine the compressive strength while the solubility of fluorine was used to represent the geo-environmental properties in term of the release of fluorine. Scan electron microscopic (SEM) test was done to identify the development of cementation compounds in the matrix of treated-bassanite soil. Test results showed that, the addition of bassanite had a significant effect on the improvement of compressive strength by increasing the amount of bassanite. Curing time had a significant effect on the increase of compressive strength, the strength increases with the increase of curing time, especially in the later curing time. The release of fluorine increases with increasing the amount of bassanite in soil mixture. The increase of water content had an indirect effect on the release of fluorine while it had a negative effect on the improvement of strength and consuming the amount of admixture. The increase of strength is associated with the decrease of the release of fluorine. Recycled bassanite, produced from gypsum wastes, had a potential to be used as a stabilizer material for MC-clay soil and meet the standards of environment.

---

Limitations in the design method used for the support systems of urban buildings make them vulnerable to damage by adjacent excavations. This paper examines a traditional system used to support excavation sites and adjacent buildings in which inclined struts are connected to the wall or foundation of the adjacent building. This method can be considered to be a type of shoring or underpinning. The performance of buildings and the criteria for deformation control during excavation are introduced. Next, a 2D finite element analysis is presented in which an excavation is modeled considering the parameters from the adjacent building and the inclined struts. The numerical model is capable of simulating the overall excavation and installation of the support system. The soil is modeled using an elastic perfectly-plastic constitutive relation based on the Mohr-Coulomb criterion. The finite element model is validated using Rankine earth pressure and in situ data was measured during an excavation. The effect of different variables on performance and acceptable limits for the inclined strut are discussed. The model used for the parametric study shows the influence of the characteristics of the adjacent building, soil parameters, geometry of excavation, type of excavation and effect of strut installation. It was found that one type of strut arrangement produced the best possible result. The results can be used as a primary approximation of small-to-medium depth excavations in which struts are used to reduce the deflections.

---

To investigate the saturation induced collapse deformation behavior of rockfill material, a set of large-scale triaxial tests were conducted in saturated and dry-saturated conditions. Specimens were tested under various confining pressures. For dry-saturated tests, specimens were sheared in various stress levels. Results of all dry saturated tests indicate a sudden reduction in the specimen volume during the submerging process. The ratio of the minimum axial strength of a submerged specimen (at the end of the saturation process) to the shear strength of the specimen before saturation is defined as the coefficient of stress recovery, Csr. Results show that this ratio increases as the confining pressure increases, and decreases as the shear stress level increases. According to the results of dry-saturated tests, reduction values of the internal friction angle caused by saturation (c), the ratio of the elasticity modulus of the material after saturation to its elasticity modulus in dry condition, i.e., Ewet/Edry, and the saturation induced sudden volumetric strain (vc) decrease as the confining pressures increase. However the shear stress level does not have any meaningful effect on the variation of c, Ewet/Edry and (vc).

---

Stabilization of earth slopes with various proposed methods is one of the important concerns of geotechnical engineering. In this practice, despite numerous developments, design conservativeness and high costs of stabilization are the issues yet to be addressed. This paper not only deals with pile location optimization but also studies the effects of the pile length by using line segments slip surface (non-circular). Taking into account the line segments slip surface in stabilization of earth slopes is a new topic which has been addressed in this paper. The line segments slip surface is actual slip surface and for determining the pile location it can lead to the actual length of the pile. The line segments critical slip surface is obtained by using the Alternating Variable Local Gradient (AVLG) optimization method. AVLG is an approach in optimization process and it is based on the Univariate method. The line segments form the initial and critical slip surface. Pile improper installation and inadequate length not only fails to increase the factor of safety, but also reduces it. The analyses are performed using the limit equilibrium (LE) method. Results of these analyses are acceptable and are properly consistent with the results obtained by other researchers.

---

Investigation of projectiles penetration phenomenon has been carried out in non-cohesive soil (Sand) targets under dry, saturated and compacted conditions. Analytical studies have been performed on the linear and non-linear soil models to obtain penetration depth formulae for ogival nose projectile and the results are verified by experimental studies. In present work, three ogival nose projectiles each having weight of 1.0 kg and nose angle of 15o, 30o and 45o are dropped from a height of 10.0 m in rectangular tank filled up by non-cohesive soil target. The rigid projectiles made an impact on a uniform target material at normal incidence with striking velocity of 14 m/s and proceeded to penetrate at rigid-body velocity. The models require geometrical parameters of the projectile types, velocity and target shear strength for the overall penetration depth of projectile. In addition, some parametric studies have been also carried out for academic and field interest.

---

In present research, 17 centrifuge tests have been conducted to study the effect of various parameters such as the number of piles, the distance between piles, gradation and thickness of the granular layer on the load-settlement behavior of a pile raft system. The results showed the importance of granular layer to reduce the settlement of non-connected pile raft system when the roles of piles are to reduce the settlement. In other words when the piles have major contribution on the bearing capacity of pile raft system, presence of a granular layer may increase the settlement.

---

In soft soil areas, equal-length piles are often adopted in the retaining system. A decrease in the bending moment value borne by the retaining structure along the pile depth (below the excavation bottom), leads to an inadequate use of the pile bending capacity near the pile bottom. This paper presents retaining systems with long and short pile combinations, in which the long piles ensure integral stability of the excavation while the short piles give full play to bearing the bending moment. For further analysis on pile and bottom heaves deformations and inner-force characteristics, three-dimensional models were built in order to simulate the stage construction of the excavation. The ratio between long and short pile numbers, and the effects on short pile length pile horizontal deformation, pile bending moment and bottom heave are investigated in detail. In the end, a feasible long-short pile combination is established. Obtained results from the simulation data and the field data prove that the long-short pile retaining system is feasible.

---

The ground improvement using Plastic Board Drain (PBD) in soft soil was undertaken by sand mat formation, PBD installation, preloading surcharge, and removal of surcharge. During this procedure, the sand mat formation induced an initial settlement. However, it was very difficult to estimate that settlement due to PBD installation, which frequently destroyed the instruments installed in the ground. Consequently, the initial settlement was not properly included in total settlement. In this study, the initial settlement was estimated using ground level measurement and cone penetration test. Both predicted almost the same amount of initial settlement. The initial settlement is linearly increased with the depth of the sand mat. The degree of consolidation and the time of surcharge removal were estimated using the settlement included the initial settlement. Correct estimation of initial settlement is very important because it is a critical factor, which affects total settlement and the time of surcharge removal. If the initial settlement is not considered, the preloading surcharge may be overloaded or the time of surcharge removal may be predicted incorrectly. Consequently, the prediction of settlement, which requires to management of construction procedure of the project, may be wrong

---

A numerical simulation of laboratory model tests was carried out to develop an understanding of the behaviour of pipes in a trench prepared with 3-Dimensional reinforced (namely "geocell-reinforced" in the present study) sand and rubber-soil mixtures, under repeated loadings. The study reports overall performance of buried pipes in different conditions of pipe-trench installations and the influence of pipe stiffness on backfill settlements, stress distribution in the trench depth and stress distribution along the pipe's longitudinal axis. Good agreements between the numerical results and experimental results were observed. The results demonstrate that combined use of the geocell layer and rubber-soil mixture can reduce soil surface settlement and pipe deflection and eventually provide a secure condition for buried pipe even under strong repeated loads.

---

The Dynamic Probe is an effective tool used in site investigation. It is more economic than the use of direct drilling, particularly in explorations with moderate depth. This paper presents an experimental study to investigate the capability of using dynamic probing to evaluate the shear strength and compaction percent of fine soil. A series of dynamic probe tests were carried out at 6 different sites in the Khozestan, Hormozgan and Qom provinces in the central and southern regions of Iran. The repeatability of the results is considered and new empirical equations relating the dynamic point resistance to undrained shear strength and compaction percent are proposed. For undrained shear strength evaluation of fine soils, i.e. clay and silty clay soils, a reliable site-specific correlation between qd and Cu can be developed when considering the correlation between log qd and log Cu. Also compaction present can be evaluated by qd. These equations can be developed to provide site-specific relationships based upon geotechnical data at each new location. Using this approach an estimation of the undrained shear strength Cu and compaction percent CP can be determined from dynamic probe tests with acceptable accuracy. The present paper also encourages the wider application of dynamic probing for site investigation in fine soils.

---

In order to improve the utilization of high liquid limit soil, the fundamental properties of high liquid limit soil and its direct utilization method are studied in this paper. This work involves both laboratory and fieldwork experiments. The results show that clay and sandy clay both with high liquid limit can be directly used for the road embankment, and the degree of compaction can be controlled at 88 %. The pack-and-cover method in accordance with Chinese technical specifications is recommended to be operated in the engineering practice. The packed height should be less than 8 meters and the total height of embankment no more than 12 meters in the interests of settlement. From the view of stability, the optimal thickness value of top sealing soil layer and edge sealing soil layer is about 1.5 meter respectively, and the geogrid reinforcement spacing should be about 2.0 meters. In addition, based on Yun-Luo expressway in China filled with high liquid limit soil, the construction techniques and key points of quality control in subgrade with pack-and-cover method are compared and discussed in detail, and the feasibility of these schemes are verified by the experimental results.

---

The distinctive characteristics of near-field earthquake records can lead to different structural responses from those experienced in far-field ones. Furthermore, soil-structure interaction (SSI) can have a crucial influence on the seismic response of structures founded on soft soils however, in most of the time has been neglected nonchalantly. This paper addresses the effects of near-field versus far-field earthquakes on the seismic response of single degree of freedom (SDOF) system with considering SSI. A total 71 records were selected in which near-field ground motions have been classified into two categories: first, records with a strong velocity pulse, (i.e. forward-directivity) second, records with a residual ground displacement (i.e. fling-step). Findings from the study reveal that pulse-type near-field records generally produce greater seismic responses than far-field motions especially at high structure-to-soil stiffness ratios. Moreover, the importance of considering SSI effects in design of structures is investigated through an example. Finally, parametric study between Peak Ground Velocity to Peak Ground Acceleration ratio (PGV/PGA) of pulse-like ground motions and maximum relative displacement indicate that with increase in structure-to-soil stiffness ratios, earthquakes with higher PGV/PGA ratio produce greater responses.

---

In this paper, a finite element model is developed for the fully hydro-mechanical analysis of hydraulic fracturing in partially saturated porous media. The model is derived from the framework of generalized Biot theory. The fracture propagation is governed by a cohesive fracture model. The flow within the fracture zone is modeled by the lubrication equation. The displacement of solid phase, and the pressure of wetting and non-wetting phases are considered as the main unknown parameters. Other variables are incorporated into the model using empirical relationships between saturation, permeability and capillary pressure. Zero-thickness element and conventional bulk element are used for propagating fracture and the surrounding media, respectively. The model is validated with respect to analytical solution of hydraulic fracture propagation problem in saturated media and then the problem is solved in semi-saturated media, considering the wetting and non-wetting pore fluid. 

---

Fly ash is one of the most plentiful and versatile of the industrial by-products. At present, nearly 150 million tonnes of fly ash is being generated annually in India posing dual problem of environmental pollution and difficulty in disposal. This calls for establishing strategies to use the same effectively and efficiently. However, it is only in geotechnical engineering applications such as the construction of embankments/dykes, as back fill material, as a sub-base material etc., its large-scale utilization is possible either alone or with soil. Soil stabilization can be achieved by various means such as compaction, soil replacement, chemical improvement, earth reinforcement etc. Usually, in the case of clay soils, chemical improvement is commonly most effective since it can strengthen the soil, to remove its sensitivity both to water and its subsequent stress history. Among chemical means or additives, fly ash/lime provides an economic and powerful means of improvement, as demonstrated by the significant transformation that is evident on mixing with heavy clay. In the present investigation, different percent fly ashes (10%, 20%, 40%, 60% & 80%) were added to a highly expansive soil from India by dry weight of the natural soil, and subjected to various tests. The important properties that are necessary for using fly ash in many geotechnical applications are index properties, compaction characteristics, compressibility characteristics, permeability and strength. Based on test results, it has been found that using fly ash for improvement of soils has a two-fold advantage. First, to avoid the tremendous environmental problems caused by large scale dumping of fly ash and second, to reduce the cost of stabilization of problematic/marginal soils and improving their engineering properties for safe construction of Engineering Structures. 

---

ABSTRACT The influence of the sand placement method above geotextile layer on interface shear strength behavior was investigated. Seven different types of woven and non woven geotextile were used with only poorly graded sand. The investigation involved placement of sand layer through inclined horizontal plane with different angles. This step constitutes a fundamental step for assessing soil to be deposited in different plane and therefore with different internal soil fabric. The interface shear strength was evaluated by using direct shear test. Although the investigated soil is uniform poorly graded sand, the influence of the deposit plane was significant especially for nonwoven geotextile. Differences in soil interface shear strength associated with the tested geotextiles samples shows that samples with higher mass per unit area and same opening sizes had the higher interface friction angle regardless the bedding plane. Influence of bedding plane on interface modulus of elasticity which used in most of interface modeling was investigated using Janbu’s formula. It is noted that the use of secant interface modulus of elasticity at 1% strain and at 50% of peak stresses gave a consistent prediction of n and Ku constant appear in Janbu’s formula for all types of geotextile. The above results were reflected in the prediction for interface molded such as Chen and Juran as shown. Therefore, the existing interface modeled is needed to be modified to account for the method that the sand is being placed above the geotextile layer.

---

This paper investigates the time dependent behaviour of Sunshine embankment on soft clay deposit with and without prefabricated vertical drains. An elasto visco-plastic model was used to investigate the influence of anisotropy and creep effect on the settlement behaviour of the embankment. The constitutive model, namely ACM accounts for combined effects of plastic anisotropy and creep. For comparison, the problem is also analysed with isotropic Modified Cam Clay model which does not consider creep effect. To analyse the PVD-improved subsoil, axisymmetric vertical drains were converted into equivalent plane strain conditions using two different mapping approaches. The results of the numerical analyses are compared with the field measurements. The numerical simulations suggest that the anisotropic creep model is able to give a better representation of soft clay response under an embankment loading. The isotropic model which neglects effects of anisotropy and creep may lead to inaccurate predictions of soft clay response. Additionally, the numerical results show that the mapping method used for PVD improved soft clays can accurately predict the consolidation behaviour of the embankment and provide a useful tool for engineering practice.

---

A study has been conducted on the bearing capacity of strip footings over sandy layered soils using the stress characteristic lines method. Traditional bearing capacity theories for specifying the ultimate bearing capacity of shallow foundations are based on the idea that the bearing layer is homogenous and infinite. However layered soils are mainly happening in practice. The stress characteristic lines method is a powerful numerical tool in order to solve stability problems in geotechnical engineering. In the present paper, an appropriate algorithm is derived for estimating the static bearing capacity of strip footing located on two layered soils using the stress characteristic lines method. Some numerical and experimental examples are presented in order to validate the proposed algorithm. Some graphs and equation are presented for initial estimating the effective depth of strip footings located on two layered soils.