---

This paper describes a series of laboratory model tests on strip footings supported on unreinforced and geogrid-reinforced sand
with an inside void. The footing is subjected to a combination of static and cyclic loading. The influence of various parameters
including the embedment depth of the void, the number of reinforcement layers, and the amplitude of cyclic load were studied.
The results show that the footing settlement due to repeated loading increased when the void existed in the failure zone of the
footing and decreased with increasing the void vertical distance from the footing bottom and with increasing the reinforcement
layers beneath the footing. For a specified amplitude of repeated load, the footing settlement is comparable for reinforced sand,
thicker soil layer over the void and much improved the settlement of unreinforced sand without void. In general, the results
indicate that, the reinforced soil-footing system with sufficient geogride-reinforcement and void embedment depth behaves much
stiffer and thus carries greater loading with lower settlement compared with unreinforced soil in the absent of void and can
eliminate the adverse effect of the void on the footing behavior. The final footing settlement under repeated cyclic loading becomes
about 4 times with respect to the footing settlement under static loading at the same magnitude of load applied.

---

Among the different ways of in-situ soil investigation, cone penetration test data are selected to evaluate the spatial variability

of geomaterials and the scale of fluctuations is chosen to evaluate the correlation structure of CPT data. In this regard six case

studies in sandy materials from Australia, U.S.A. and Iraq are selected. Various techniques for the calculation of the scale of

fluctuation of geotechnical parameters are suggested in literature e.g. VXP, SAI, AMF, BLM and VRF without any preference or

privilege for any specific procedure. In order to isolate the stochastic portion of cone tip resistance, deterministic trend was first

removed by regression analysis. This study suggests that quadratic trend removal is more suitable for selected CPT data

soundings. The closeness of the estimated scale of fluctuation using different approaches is assessed too. Mean value of the scale

of fluctuation by five established methods ranges between 0.44 to 1.52 meter for six different cases and the coefficient of

variation for the scale of fluctuation calculated by these methods varies between 12 to 27 % showing that available established

methods produce almost compatible and comparable results.

---

Piles or drilled shafts used in bridge foundation, waterfronts, and high rise buildings are generally subjected to lateral loads. In order to study the effect of concrete pile geometry on the structural behavior in layered soils, several models with different shapes and dimensions for piles and different properties for two soil layers with variable thickness were selected and analyzed using the finite difference method. The performance of piles situated in layered granular soil with different compaction and thicknesses were studied in two cycles of lateral loading and unloading. The applied finite difference procedure is also validated based on experimental and published results. The pile head displacement of different models due to their overall deformation and rotation were calculated under maximum loading. For a comparison of pile head displacement due to their overall deformation and rotation in different models, the "performance index” is defined as the ratio of “displacement due to deformation” to the “total displacement”.

---

Soil reinforced with fiber shows characteristics of a composite material, in which fiber inclusion has a significant effect on soil permeability. Concerning to the higher void ratio of carpet fibers, at first stages it may be expected that an increase in fiber content of the reinforced soil would result in an increase in permeability of the mixture. However, the present article demonstrates that fiber inclusion will decrease the permeability of sand-fiber composite.A series of constant head permeability tests have been carried out to show the effects and consequently, a new system of phase relationships was introduced to calculate the dry mass for the sand portion of the composite. Monte Carlo simulation technique adopted with finite element theory was employed to back calculate the hydraulic conductivity of individual porous fibers from the laboratory test results. It was observed that the permeability coefficient of the porous fibers are orders of magnitude less than the skeletal sand portion due to the fine sand particle entrapment and also the fiber volume change characteristics.

---

This paper presents a simple solution based on the limit equilibrium of sliding soil wedge of reinforced backfill subjected to the horizontal acceleration in the framework of the pseudo-static method. In particular, contrary to most studies on the reinforced retaining wall, the solution proposed in this study, takes into account the effect of the uniform surcharge on the reinforced backfill soil and of its distance from the face of the wall. The results are investigated in dimensionless form of the maximum reinforcement required strength (Kmax), the dimension of the sliding wedge (Lc/H), and the factor of safety (FS). Compared to the reinforced backfill without surcharge, the presence of surcharge over the reinforced backfill and of its distance from the top of the backfill have significant effects on the stability of the system. For a fixed surcharge, a minimum distance of surcharge exists for which the presence of the surcharge does not affect the solution and the failure mechanism is that corresponding to the case of system with no surcharge. A detailed design example is included to illustrate usage of proposed procedures. Comparisons of the present results with available results show a favorable agreement.

---

In this technical note, a methodology is introduced for reliability calculation of consolidation settlement based on cone penetration test (CPT) data. The present study considers inherent soil variability which influences consolidation settlements results. To proceed reliability analysis, the measured data of a sample corrected cone tip resistance (􀝍􀯧) is detrended using a quadratic trend and the residuals are assumed to be lognormally distributed random field. Realizations of 􀝍􀯧 is generated by using spatial variability of residuals including standard deviation and the scale of fluctuation. The quadratic trend and the generated residuals are then combined to correlate shear and bulk modulus as input consolidation properties for coupled analysis and subsequently consolidation settlement was calculated by using finite difference method adopted in Monte Carlo simulations. The results of reliability analysis are presented describing the range of possible settlements by considering characteristics of uncertainties involved at the particular site. Number of realizations rendering settlements smaller than the allowable settlement must be such that guarantee proper performance or acceptable reliability index.

---

In this study digital image correlation (DIC) technique combined with a high speed video system was used to predict movement of particles in a water model. Comparing with Particle-image velocimetry (PIV) technique, it provides a low cost alternative approach to visualize flow fields and was successfully employed to predict the movement of particles in a water model at different submergence depth using gas injection. As the submergence depth increases, the number of the exposed eye is reduced accordingly. At 26.4 cm submergence depth, an exposed eye was found at 1/3 of the submergence depth, whereas two exposed eyes were observed at 1/2 depth and near the bottom wall at 24 cm submergence depth.

---

A review of literature reveals that although singly curved conical shells applicable in many fields of mechanical engineering have been studied by many researchers but doubly curved conoidal shells which are very popular as civil engineering roofing units have not received due attention. Hence relative performances of composite conoidal shells in terms of displacements and stress resultants are studied in this paper under static and dynamic loadings. Free vibration frequencies are also reported. A curved quadratic isoparametric eight noded element is used to model the shell surface. Clamped and simply supported boundary conditions are considered. Results obtained from the present study are compared with established ones to check the correctness of the present approach. A number of additional problems of composite conoidal shells are solved for eight different stacking sequences of graphite-epoxy composite for each of the edge conditions. Uniformly distributed load for static bending analysis and step load of infinite duration for solution of forced vibration problem are considered. The results are interpreted from practical application standpoints and findings that are important for a designer to note, before he decides on the shell combination he will finally adopt among a number of possible options, are highlighted.

---

In this paper, different aspects of the behavior of 2×2 pile groups under liquefaction-induced lateral spreading in a 3-layer soil profile is investigated using large scale 1-g shake table test. Different parameters of the response of soil and piles including time-histories of accelerations, pore water pressures, displacements and bending moments are presented and discussed in the paper. In addition, distribution of lateral forces due to lateral spreading on individual piles of the groups is investigated in detail. The results show that total lateral forces on the piles are influenced by the shadow effect as well as the superstructure mass attached to the pile cap. It was also found that lateral forces exerted on the piles in the lower half of the liquefied layer are significantly larger than those recommended by the design code. Based on the numerical analyses performed, it is shown that the displacement based method is more capable of predicting the pile group behavior in this experiment comparing to the force based method provided that the model parameters are tuned.

---

This research shows the results of studies carried out to define and analyze the effect of aging on MSW behavior of Kahrizak Landfill, the biggest landfill in Iran. Studied samples consisted of fresh samples and also aged ones with 5.5, 14 and 21 years of age which were obtained by mechanical excavators in aged burial locations. Analyzing variation in MSW components illustrates that paste fraction of MSW decreases due to aging process while fibers show a rising trend. Also the moisture content and the organic content of MSW reduce below half of the initial values while the degree of decomposition (DOD) increase up to almost 60% after 14 years. These variations over the time are significantly related to the burying methods and environmental condition of burying location. Shear strength behavior of MSW material was analyzed by some CU tests using large scale triaxial apparatus (D=150mm, H=300mm) on remolded MSW specimens. General observations depict that with an increase in strain level, loading rises without any peak point on stress-strain curves. Fresh samples represent the lowest shear strength followed by 21, 14 and 5.5 year-old samples respectively. There is a direct relationship between fiber content and shear strength. Internal friction angle of aged samples decreases in comparison with fresh ones while cohesion has an inverse trend and rises over the time. According to the effect of burying condition on MSW characteristics, it seems that DOD factor is a more appropriate factor than age in order to analyze long-term behavior of MSW.

---

The previous studies show that a high percentage of traffic accidents take place in two-lane rural highways and most of which happen at horizontal curves. Meanwhile the horizontal alignment is often subject to hard topographic conditions where because of economic aspects designers are forced to design horizontal curves at grades. Vertical angle of longitudinal slope reduces the normal force of vehicle on road and friction force in tire-pavement surface will decrease. This leads to a lack of sufficient driver control over the vehicle especially if the curve with small radius is located at downgrade. In this paper, the suitability of operating speed and lateral friction coefficient as geometric design criteria for horizontal curves in downgrades are studied with regard to traffic safety and vehicle stability. The investigation of speed reduction of the vehicles running on a horizontal curve at downgrade as a response of driver behavior and the use of friction ellipse theory give the available friction coefficient. Whereas the dynamic analysis of forces applied on the vehicle in curve which is located at downgrade if combined with operating speed results in the required coefficient of lateral friction. Finally, a comparison of these two parameters based on safety evaluation criteria gives an estimation of actual safety level in designing horizontal curve at downgrades with regard to AASHTO’s data in horizontal curve design.

---

In the water industry tunnels can be used to transfer water from a basin to other areas over varying distances. The construction of such tunnels is inherently risky and can result in unpredicted events and incidents. It is therefore necessary that thorough risk assessments are carried out as a priority of the owner, contractor and consultant organization. This is so that, through a systematic and logical plan, they can risk posed by these unforeseen events and incidents. In this paper, the risks and their main causes which are often encountered in such projects are identified and assessed. A fault tree method is applied in order to identify the main causes of events and incidents. By its nature a Risk assessment cannot be defined by absolute values and so fuzzy data must be used in order to calculate the probability of incidence and the severity of the risk. This is done on the four main criteria of time, cost, quality and safety. In order to estimate the significance of each criterion and to calculate the significance of the total influence of risk Analytic Hierarchy Process (AHP) is applied. In this paper the case study of Dasht-e Zahab water conveyance tunnel has been selected for discussion as it was subjected to severe and multiple hazards. The results obtained using the method were validated by conducting different interviews with the field experts. It was concluded that by applying the proposed methodology on the case study the risks of the project can be evaluated in a more methodical and accurate way than could be done without using the method. This approach is therefore recommended for similar types of projects where there are complicated risks that must be thoroughly investigated and understood.

---

The use of recycled bassanite, produced from gypsum wastes, in ground improvement projects is initiated recently in Japan to eliminate the huge quantities of gypsum wastes. Meanwhile the use of recycled bassanite has a positive effect on the environment and economy, it has many challenges. These challenges are related to the release of fluorine more than the standard limits results in contaminated fluorine soil. This research investigates the effect of the amount of bassanite, and water content on the release of fluorine from MC-clay soil stabilized with bassanite, taking in consideration their effect on the compressive strength. Recycled bassanite was mixed with furnace cement with a ratio of 1:1 to prevent the solubility of bassanite. Different amounts of this admixture were mixed with the tested soil at different water contents. Unconfined compression test was used to determine the compressive strength while the solubility of fluorine was used to represent the geo-environmental properties in term of the release of fluorine. Scan electron microscopic (SEM) test was done to identify the development of cementation compounds in the matrix of treated-bassanite soil. Test results showed that, the addition of bassanite had a significant effect on the improvement of compressive strength by increasing the amount of bassanite. Curing time had a significant effect on the increase of compressive strength, the strength increases with the increase of curing time, especially in the later curing time. The release of fluorine increases with increasing the amount of bassanite in soil mixture. The increase of water content had an indirect effect on the release of fluorine while it had a negative effect on the improvement of strength and consuming the amount of admixture. The increase of strength is associated with the decrease of the release of fluorine. Recycled bassanite, produced from gypsum wastes, had a potential to be used as a stabilizer material for MC-clay soil and meet the standards of environment.

---

Self-centering pier (SCP) has been viewed as a remarkable accomplishment which is able to sustain major lateral loading with reduced structure damage in seismic engineering. Stiffness deterioration observed in experiment is vital for the seismic performance of self-centering concrete pier. In this contribution, the associated stiffness deterioration with respect to the structural damage is modeled in a modified analytical model for SCP comprehensively. In the proposed modified theoretical model, the lateral force-displacement relation associated with the stiffness reducing is analyzed. Three damage factors are introduced in the stiffness deterioration analysis to illustrate the damage evolution caused by gradually increasing lateral displacement. The proposed modified quasic-static model with damage evolution or stiffness deterioration has been validated against an experiment we conducted, where a good agreement is clearly evident. Subsequently, a parametric investigation focusing on aspect ratio, initial pre-tension, and ratio of ED (Energy Dissipator) was conducted to evaluate the hysteretic behavior of SCP under quasi-statically cyclic loading.

---

A numerical simulation of laboratory model tests was carried out to develop an understanding of the behaviour of pipes in a trench prepared with 3-Dimensional reinforced (namely "geocell-reinforced" in the present study) sand and rubber-soil mixtures, under repeated loadings. The study reports overall performance of buried pipes in different conditions of pipe-trench installations and the influence of pipe stiffness on backfill settlements, stress distribution in the trench depth and stress distribution along the pipe's longitudinal axis. Good agreements between the numerical results and experimental results were observed. The results demonstrate that combined use of the geocell layer and rubber-soil mixture can reduce soil surface settlement and pipe deflection and eventually provide a secure condition for buried pipe even under strong repeated loads.

---

Pre-cast concrete products are sometimes manufactured in 2 cycles per day with one mold for the purpose of productivity improvement and so forth. In such a case, from the point of view of securing early-time strength which is required at the time of demolding, it is necessary to increase steam curing temperature and then the likelihood of temperature cracking becomes a concern. Moreover, self-compacting concrete (hereinafter refer as “SCC”) is increasingly used to which ground granulated blast-furnace slag is added, in consideration of environment surrounding a plant or operation environment. One choice then is to admix expansive agent in order to prevent cracking due to autogenous shrinkage. However, there is some possibility that high temperature curing required for 2 cycles per day production likely enhances cracking due to expansive agent admixing. In this study, the cause of cracking of large-sized pre-cast concrete products with high amount of expansive agent, in comparison of 1 cycle per day and 2 cycles per day productions was investigated.

As the result, it was confirmed that high temperature steam curing and early demolding of 2 cycles per day production promote thermal stress cracking in contrast to 1 cycle per day production, and at the same time, un expected cracking along main reinforcement is caused by excess expansion due to inappropriate curing of expansive agent.

---

Colored self-compacting mortar (C-SCM) is a novel cementitious product that has been recently used in decoration and rehabilitation and has improved aesthetic quality of architectural constructions. C-SCM is susceptible to strength decrease due to excessive pigment presence in the mixture. Optimum pigment content with respect to color intensity and mechanical performance is an important matter that should be determined to prevent mortar failure after construction. In this research, two inorganic pigments in production of colored self-compacting mortar were utilized. The impact of titanium dioxide (TiO2) and iron hydroxide (FeO(OH)) contents on behavior of C-SCMs were investigated in white and gray cement matrixes. Experiments included measurements of compressive strength of mortar cubes and cylinders, flexural strength and colorimetric properties. Analyses on compressive and flexural toughness were applied, as well. It was concluded that pigment content in mix design of colored self-compacting mortar could be optimized with regard to color quality in surface and mechanical strength of the product. Results implied that 5 and 2% of titanium dioxide were the saturation points of color and strength respectively and iron hydroxide at 10% was unsurpassed in C-SCMs containing white cement. Application of both pigments in gray SCMs caused the saturation points of color and strength to occur at 10 and 2%, respectively.

---

Compressive strength is as one of the most important properties of concrete and mortar that its measurement may be necessary at both early and later ages. Prediction of compressive strength by a proper model is a fast and cost-effective way for evaluating cement quality under various curing conditions. In this paper, a logarithmic model based on the results of an experimental work conducted to investigate the effects of curing time and temperature on the compressive strength development of chemically activated high phosphorous slag content cement has been presented. This model is in terms of curing time and temperature as independent variables and compressive strength as dependent variable. For this purpose, mortar specimens were prepared from 80 wt.% phosphorous slag, 14 wt.% Portland cement, and 6 wt.% compound chemical activator at Blaine fineness of 303 m2/kg. The specimens were cured in lime-saturated water under temperatures of 25, 45, 65, 85 and 100 ºC in oven. The model has two adjustable parameters for various curing times and temperatures. Modeling has been done by applying dimensionless insight. The proposed model can efficiently predict the compressive strength of this type of high phosphorous slag cement with an average relative error of less than 4%.

---

The present study demonstrates the influence of operating speed on capacity of a midblock section of urban road. Speed – flow data collected at 12 midblock sections of 6-lane and 4-lane divided urban arterials in four metropolitan cities of India are analyzed to determine their capacity. Lane capacity was found to vary from 1482 pcu/hr to 2105 pcu/hr. This variation is explained on the basis of city size and driving behavior, which would influence the free flow speed on the road. Free flow speed was also measured at each section and these speed data were used to determine operating speed (85th percentile of free flow speed of standard car) on the road. Lane capacity was found to be strongly related with operating speed on a road and a second degree polynomial model is developed between the lane capacity and operating speed. This model is further validated by collecting speed flow data at two new sections and their capacity was estimated from field data and from the model developed in the study. The predicted capacity was found to be matching with field capacity and the maximum error was 0.10 percent. Operating speed on a road can vary due to road surface condition, side friction or similar other factors. All these will have influence on capacity of the road. The capacity model suggested in the present study can be a useful tool to determine capacity of an urban road from its operating speed data.

---

In recent times, Bus Arrival Time Prediction (BATP) systems are gaining more popularity in the field of Advanced Public transportation systems (APTS), a major functional area under Intelligent Transportation Systems (ITS). BATP systems aim to predict bus arrival times at various bus stops and provide the same to passenger’s pre-trip or while waiting at bus stops. A BATP system, which is accurate, is expected to attract more commuters to public transport, thus helping to reduce congestion. However, such accurate prediction of bus arrival still remains a challenge, especially under heterogeneous and lane-less traffic conditions such as the one existing in India. The uncertainty associated with such traffic is very high and hence the usual approach of prediction based on average speed will not be enough for accurate prediction. In order to make accurate predictions under such conditions, there is a need to identify correct inputs and suitable prediction methodology that can capture the variations in travel time. To accomplish the above goal, a robust framework relying on data analytics is proposed in this study. The spatial and temporal patterns in travel times were identified in real time by performing cluster analysis and the significant inputs thus identified were used for the prediction. The prediction algorithm used the Adaptive Kalman Filter approach, in order to take into account of the high variability in travel time. The proposed schemes were corroborated using real-world GPS data and the results obtained are very promising.