Search published articles


Showing 11 results for Reinforced Concrete Beam

Khalou A.r., Ghara Chour Lou A.,
Volume 3, Issue 1 (3-2005)
Abstract

This paper presents the results of analytical studies concerning the flexuralstrengthening of reinforced concrete beams by external bonding of high-strength lightweightcarbon fiber reinforced plastic (CFRP) plates to tension face of the beam. Three groups of beamswere tested analytically and compared with existing experimental results. Results of the numericalanalyses showed that, although addition of CFRP plates to the tension face of the beam increasesthe strength, it decreases the beam ductility. Finite element modeling of fifteen different beams in aparametric study indicates that steel area ratio, CFRP thickness, CFRP ultimate strength andelastic modulus considerably influence the level of strengthening and ductility.
F.m. Wegian, M.t. Alkhamis, S.r. Sabbagh Yazdi,
Volume 4, Issue 4 (12-2006)
Abstract

This study evaluates two different types of techniques for concrete hollow-block sections reinforced with traditional steel rebars and wire meshes, and compares their structural behaviour to that of an ordinary reinforced concrete beam section. The comparisons are based on the responses both before and after they were repaired with glass fibre reinforced polymers (GFRP). The specimens were subjected to concentrated loading up to initial failure. After failure, the specimens were repaired and loaded once again until ultimate failure. It was shown that the success of the repair by GFRP depended on the mode of failure of the hollow-block concrete beams.
Ali Kheyroddin, Hosein Naderpour,
Volume 5, Issue 1 (3-2007)
Abstract

A parametric study is performed to assess the influence of the tension reinforcement index, ( ω = ρ fy /f Bc), and the bending moment distribution (loading type) on the ultimate deformation characteristics of reinforced concrete (RC) beams. The analytical results for 15 simply supported beams with different amounts of tension reinforcement ratio under three different loading conditions are presented and compared with the predictions of the various formulations and the experimental data, where available. The plastic hinge rotation capacity increases as the loading is changed from the concentrated load at the middle to the third-point loading, and it is a maximum for the case of the uniformly distributed load. The effect of the loading type on the plastic rotation capacity of the heavily reinforced beams is not as significant as that for the lightly reinforced beams. Based on the analytical results obtained using the nonlinear finite element method, new simple equations as a function of the tension reinforcement index, ω, and the loading type are proposed. The analytical results indicate that the proposed equations can be used for analysis of ultimate capacity and the associated deformations of RC beams with sufficient accuracy.
A.r. Khaloo, I. Eshghi, P. Piran Aghl,
Volume 8, Issue 3 (9-2010)
Abstract

In this paper the response of cantilevered reinforced concrete (RC) beams with smart rebars under static lateral loading has been numerically studied, using Finite Element Method. The material used in this study is SuperelasticShape Memory Alloys (SE SMAs) which contains nickel and titanium elements. The SE SMA is a unique alloy that has the ability to undergo large deformations and return to their undeformed shape by removal of stresses. In this study, different quantities of steel and smart rebars have been used for reinforcement andthe behavior of these models under lateral loading, including their load-displacement curves, residual displacements, and stiffness, were discussed. During lateral loading, rebars yield or concrete crushes in compression zone in some parts of the beams and also residual deflections are created in the structure. It is found that by using SMA rebars in RC beams, these materials tend to return to the previous state (zero strain), so they reduce the permanent deformations and also in turn create forces known as recovery forces in the structure which lead into closing of concrete cracks in tensile zone. This ability makes special structures to maintain their serviceability even after a strong earthquake


M. Z. Kabir, A. Hojatkashani,
Volume 10, Issue 4 (12-2012)
Abstract

The aim of current study is to investigate the effect of Carbon Fiber Reinforced Polymer (CFRP) composites on the fatigue

response of reinforced concrete beams. 6 reinforced concrete (RC) beams from which 3 were retrofitted with CFRP sheets, were

prepared and subjected to fatigue load cycles. To predict and trace the failure occurrence and its growth, a small notch was

induced at the middle span in bottom surface of all RC specimens. At the certain points, strains in concrete and CFRP were

measured in each cycle. The upper limit of applied load was considered at the level of design service load of bridges. In addition,

strain measurements facilitated to the calculation of interfacial shear stresses between concrete substrate and the CFRP layer.

The variation of such stresses through load cycles has been presented and discussed. Also, a discussion on possibility of the local

debonding phenomenon resulted from such interfacial stresses was presented. Load–deflection curves, strain responses and

propagation of tensile cracks provided an insight on the performance of the CFRP strengthened beams subjected to different

cycles of fatigue loading. Variation of load-deflection curves through fatigue load cycles depicted stiffness degradation which

was discussed in the research.


C. Torres-Machi, V. Yepes, J. Alcala, E. Pellicer,
Volume 11, Issue 2 (6-2013)
Abstract

This paper describes a methodology in designing high-performance concrete for simply supported beams, using a hybrid optimization strategy based on a variable neighborhood search threshold acceptance algorithm. Three strategies have been applied to discrete optimization of reinforced concrete beams: Variable Neighborhood Descent (VND), Reduced Neighborhood Search (RNS) and Basic Variable Neighborhood Search (BVNS). The problem includes 14 variables: two geometrical one material type one mix design and 10 variables for the reinforcement setups. The algorithms are applied to two objective functions: the economic cost and the embedded CO2 emissions. Firstly, this paper presents the application of these three different optimization strategies, which are evaluated by fitting the set of solutions obtained to a three-parameter Weibull distribution function. The Variable Neighborhood Descent with Threshold Accepting acceptance strategy algorithm (VND-TA) results as the most reliable method. Finally, the study presents a parametric study of the span length from 10 to 20 m in which it can be concluded that economic and ecological beams show a good parabolic correlation with the span length.
R. Abbasnia, A. Farsaei,
Volume 11, Issue 3 (9-2013)
Abstract

Corrosion of reinforcing steel and other embedded metals is the main cause of severe deterioration in reinforced concrete structures which subsequently imposes adverse effects on ultimate and serviceability limit state performance of the whole structure. In this paper, a new corrosion detection method for reinforced concrete beams, based on wavelet analysis is presented. To evaluate the capability and efficiency of the method, a simply supported RC beam was modeled in 3-D taking into account the behaviors of concrete, steel and bond degradation. Deflection profile and mode shapes were extracted numerically and analyzed by wavelet transform. From the findings of the modeling, it can be concluded that this wavelet-based method is capable of detecting corrosion at its earliest stage. It is also concluded that both discrete and continuous wavelet transforms can be used and mother wavelet type has no significant effect on the results.
S. Karimiyan, A. Moghadam, A. . Husseinzadeh Kashan, M. Karimiyan,
Volume 13, Issue 1 (3-2015)
Abstract

Plan irregularity causes local damages being concentrated in the irregular buildings. Progressive collapse is also the collapse of a large portion or whole building due to the local damages in the structure. The effect of irregularity on the progressive collapse potential of the buildings is investigated in this study. This is carried out by progressive collapse evaluation of the asymmetric mid rise and tall buildings in comparison with the symmetric ones via the nonlinear time history analyses in the 6, 9 and 12 story reinforced concrete buildings. The effect of increasing the mass eccentricity levels is investigated on the progressive collapse mechanism of the buildings with respect to the story drift behavior and the number of beam and column collapsed hinges criteria. According to the results, increasing the mass eccentricity levels causes earlier instability with lower number of the collapsed hinges which is necessary to fail the asymmetric buildings and at the same time mitigates the potential of progressive collapse. Moreover, the decreasing trend of the story drifts of the flexible edges is lower than those of the stiff edges and the mass centers and the amount of decrement in the story drifts of the stiff edges is approximately similar to those of the mass centers.
K. Wang, S.f. Yuan, D.f. Cao, W.z. Zheng,
Volume 13, Issue 2 (6-2015)
Abstract

This paper describes experimental and numerical investigations on two specimens of frames composed of steel reinforced concrete beam and angle-steel concrete column under horizontal low cyclic loading. Based on the test results, the relationship curves of the horizontal load-displacement and the failure modes are acquired. Meanwhile the hysteretic behaviors, skeleton curves, stiffness degradation, energy dissipation, residential deformation of the two specimens are studied. Nonlinear structural analysis program OpenSEES is employed to predict the experimental curves. Using the verified numerical model, the influences of slenderness ratio, axial compression ratio, steel ratio of column, cross-section moment resistance of I-shaped steel in beam, ratio of longitudinal rebars of beam and prestressing level on skeleton curves are investigated. The results indicated that the two specimens exhibited the favorable ductility and energy dissipation capacity, and the beam depth could be reduced to improve service function because of the application of the prestress. The ultimate horizontal load decreases with the increase of column slenderness ratio, and firstly increases then decreases with the increase of axial compression ratio. In the meantime, the descent segment of skeleton curve is smooth with the increase of column slenderness ratio, and becomes steeper with the increase of axial compression ratio.
Guray Arslan, Muzaffer Borekci, Muzaffer Balci, Melih Hacisalihoglu,
Volume 14, Issue 3 (4-2016)
Abstract

The contribution of concrete to inelastic deformation capacity and shear strength of reinforced concrete (RC) columns failing in shear has been investigated extensively by various researchers. Although RC members are designed to have shear strengths much greater than their flexural strengths to ensure flexural failure according to the current codes, shear degradation of RC columns failing in flexure has not been studied widely. The aim of this study is to investigate the shear degradation of RC columns using finite element analyses (FEA). The results of FEA are compared with the results of experimental studies selected from literature, and it is observed that the lateral load-deflection curves of analysed columns are compatible with the experimental results. Twenty-six RC columns were analysed under monotonically increasing loads to determine the concrete contribution to shear strength. The results of analyses indicate that increasing the ratio of shear to flexural strength reduces the concrete contribution to shear strength of the columns.


Vahid Broujerdian, Mohammad T. Kazemi,
Volume 14, Issue 8 (12-2016)
Abstract

Complex nature of diagonal tension accompanied by formation of new cracks as well as closing and propagating preexisting cracks has deterred researchers to achieve an analytical and mathematical procedure for accurate predicting shear behavior of reinforced concrete, and there is the lack of a unique theory accepted universally. Shear behavior of reinforced concrete is studied in this paper based on recently developed constitutive laws for normal strength concrete and mild steel bars using nonlinear finite element method. The salient feature of these stress-strain relations is to account the interactive effects of concrete and embedded bars on each other in a smeared rotating crack approach. Implementing the considered constitutive laws into an efficient secant-stiffness based finite element algorithm, a procedure for nonlinear analysis of reinforced concrete is achieved. The resulted procedure is capable of predicting load-deformation behavior, cracking pattern, and failure mode of reinforced concrete. Corroboration with data from shear-critical beam test specimens with a wide range of properties showed the model to predict responses with a good accuracy. The results were also compared with those from the well-known theory of modified compression field and its extension called disturbed stress field model which revealed the present study to provide more accurate predictions. 



Page 1 from 1     

© 2020 All Rights Reserved | International Journal of Civil Engineering

Designed & Developed by : Yektaweb