Search published articles


Showing 51 results for Column

Mazloom M., Ramezanian Pour A.a.,
Volume 2, Issue 1 (3-2004)
Abstract

This paper presents the long-term deformations of reinforced high-strength concrete columns subjected to constant sustained axial forces. The objective of the study was to investigate the effects of binder systems containing different levels of silica fume on time-dependent behaviour of high-strength concrete columns. The experimental part of the work focused on concrete mixes having a fixed water/binder ratio of 0.35 and a constant total binder content of 500 kg/m3. The percentages of silica fume that replaced cement in this research were: 0%, 6%, 8%, 10% and 15%. The mechanical properties evaluated in the laboratory were: compressive strength secant modulus of elasticity strain due to creep and shrinkage. The theoretical part of the work is about stress redistribution between concrete and steel reinforcement as a result of time-dependent behaviour of concrete. The technique used for including creep in the analysis of reinforced concrete columns was age-adjusted effective modulus method. The results of this research indicate that as the proportion of silica fume increased, the short-term mechanical properties of concrete such as 28-day compressive strength and secant modulus improved. Also the percentages of silica fume replacement did not have a significant influence on total shrinkage however, the autogenous shrinkage of concrete increased as the amount of silica fume increased. Moreover, the basic creep of concrete decreased at higher silica fume replacement levels. Drying creep (total creep - basic creep) was negligible in this investigation. The results of the theoretical part of this researchindicate that as the proportion of silica fume increased, the gradual transfer of load from the concrete to the reinforcement decreased and also the effect of steel bars in lowering the concrete deformation reduced. Moreover, the total strain of concrete columns decreased at higher silicafume replacement levels.
B. Behnam, M.h. Sebt, H.m. Vosoughifar,
Volume 4, Issue 2 (6-2006)
Abstract

By identifying the damage index of a structure, in addition to a correct understanding from real behavior of the structure, the required criterion for strengthening would be given. Researchers have given many relations for determination of damage index but such relations have been based upon laboratory methods which challenge their usage in a broad term. In this paper two new methods are given for calculation of damage index. Surveying the first crack limit and total structure failure is based upon the formation of plastic joints in the first column and basic floor columns. To give a qualitative simple and functional damage index, the functional method was given in the form of a qualitative method with statistical analysis and collection of different views. Using this method is very simple and meantime offers suitable accuracy. With a numerical study on three models it was made clear that the difference of new method with amended method of Papadopolos in approximate 3%. This shows that given qualitative method is suitable to be used in a broad terms.
A. Haddad, Gh. Shafabakhsh,
Volume 5, Issue 2 (6-2007)
Abstract

Local site conditions have a strong effect on ground response during earthquakes. Two important soil parameters that control the amplification effects of seismic motions by a soil column are the soil hysteretic damping ratio and shear wave velocity. This paper presents the results of in situ damping ratio measurements performed using continuous surface wave attenuation data at a site in Semnan University campus and analysis used to obtain the near surface soils damping ratio profile. Once the frequency dependent attenuation coefficients are determined, the shear damping ratio profile is calculated using an algorithm based on constrained inversion analysis. A computer code is developed to calculate the shear damping ratio in each soil layer. Comparisons of the in situ shear damping ratio profile determined from continuous surface wave with cross hole independent test measurements are also presented. Values of shear damping ratio, obtained using continuous surface wave measurements, were less than the measured using cross hole tests, possibly because of the higher frequencies used in cross hole tests.
S. Eshghi, V. Zanjanizadeh,
Volume 5, Issue 3 (9-2007)
Abstract

This paper presents an experimental study on seismic repair of damaged square reinforced concrete columns with poor lap splices, 90-degree hooks and widely spaced transverse bars in plastic hinge regions according to ACI detailing (pre.1971) and (318-02) using GFRP wraps. Three specimens were tested in “as built” condition and retested after they were repaired by glass fiberreinforced plastic sheets. They were tested under numerous reversed lateral cyclic loading with a constant axial load ratio. FRP composite wraps were used for repairing of concrete columns in critically stressed areas near the column footings. Physical and mechanical properties of composite wraps are described. Seismic performance and ductility of the repaired columns in terms of the hysteretic response are evaluated and compared with those of the original columns. The results indicated that GFRP wraps can be an effective repair measure for poorly confined R/C columns due to short splice length and widely spaced ties with 90-degree anchorage hooks. Both flexural strength and ductility of repaired columns were improved by increasing the existing confinement in critical regions of them.
Sassan Eshghi, Khashaiar Pourazin,
Volume 7, Issue 1 (3-2009)
Abstract

Confined masonry buildings are used in rural and urban areas of Iran. They performed almost satisfactory

during past moderate earthquakes of Iran. There is not a methodology in Iranian Seismic Code (Standard 2800-3rd

edition) to estimate their capacities quantitatively. In line with removing this constraint, an attempt is made to study

in-plane behavior of two squared confined masonry walls with and without opening by using a numerical approach.

These walls are considered based on Iranian Seismic Code requirements. Finite element 2D models of the walls are

developed and a pushover analysis is carried out. To model the non-linear behavior of the confined masonry walls, the

following criteria are used: (1) The Rankine-Hill yield criterion with low orthotropic factor to model the masonry

panel (2) The Rankine yield criterion to model reinforced concrete bond-beams and tie-columns (3) The Coulomb

friction criterion with tension cutoff mode to model the interface zone between the masonry panel and reinforced

concrete members. For this purpose, the unknown parameters are determined by testing of masonry and concrete

samples and by finite element analysis. Comparing the results show that the initial stiffness, the maximum lateral

strength and the ductility factor of walls with and without opening are different. Also, the severe compressed zones of

the masonry panels within the confining elements are found different from what are reported for the masonry panels

of infilled frames by other researchers. This study shows that a further investigation is needed for estimating capacity

of confined masonry walls with and without opening analytically and experimentally. Also where openings, with

medium size are existed, the confining elements should be added around them. These issues can be considered in the

next revisions of Iranian Seismic Code.


M. Saiidi, C. Cruz, D. Hillis,
Volume 8, Issue 1 (3-2010)
Abstract

Three unconventional details for plastic hinges of bridge columns subjected to seismic loads were developed,

designed, and implemented in a large-scale, four-span reinforced concrete bridge. Shape memory alloys (SMA),

special engineered cementitious composites (ECC), elastomeric pads embedded into columns, and post-tensioning

were used in three different piers. The bridge model was subjected to two-horizontal components of simulated

earthquake records of the 1994 Northridge earthquake in California. The multiple shake table system at the University

of Nevada, Reno was used for testing. Over 300 channels of data were collected. Test results showed the effectiveness

of post-tensioning and the innovative materials in reducing damage and permanent displacements. The damage was

minimal in plastic hinges with SMA/ECC and those with built in elastomeric pads. Conventional reinforced concrete

plastic hinges were severely damaged due to spalling of concrete and rupture of the longitudinal and transverse

reinforcement. Analytical studies showed close correlation between the results from the OpenSEES model and the

measured data for moderate and strong earthquakes.


S.m. Mir Mohammad Hosseini, A.a. Hajimohammadi, A. R. Hajimohammadi,
Volume 8, Issue 2 (6-2010)
Abstract

Seismic piezocone device (SCPTu) together with Resonant Column and Cyclic Triaxial test apparatus are

employed to measure small strain shear modulus (G0) of carbonate sandy and clayey soils of southern coasts of Iran.

A large area of southern regions of Iran is formed from clay, silt and sand. In this study, maximum shear modulus that

is derived from both field (by seismic piezocone) and laboratory (by Resonant Column and Cyclic Triaxial) tests on

soil samples from the southern region, indicated a meaningful effect of sample disturbance. Results show that in

laboratory tests, loose samples tend to become denser and therefore exhibit greater stiffness whereas dense samples

tend to become looser, showing a reduction in stiffness. According to the results of the present study, there are narrow

limits of soils shear moduli for which the laboratory tests and the field measurements yield approximately the same

amounts. This limit of shear moduli is about 30-50(MPa) for clay deposits and 70-100 (MPa) for sandy deposits. Since

the shear moduli of soils in small strains can also be computed from the shear wave velocity, also correlations based

on parameters derived from SCPTu test for shear wave velocity determination of sandy and clayey soils of the studied

area are presented. This study shows that shear wave velocity can be related to both corrected tip resistance and total

normal stress. The measurements of the damping ratio and shear module, because of a great disturbance of stiff

deposits during the sampling process and also due to considerable differences between the laboratory and field

results, by the laboratory approaches are not reliable and advised.


Rouzbeh Dabiri, Faradjollah Askari, Ali Shafiee, Mohammad Kazem Jafari,
Volume 9, Issue 2 (6-2011)
Abstract

Laboratory data, which relate the liquefaction resistance of Firoozkooh sand and non-plastic silt mixtures to shear wave velocity are

presented and compared to liquefaction criteria derived from seismic field measurements by Andrus and Stokoe [1]. In the work

described herein, cyclic triaxial and resonant column tests were conducted on specimens of clean sand and sand-silt mixtures with silt

content up to 60%, prepared at different densities. Cyclic undrained strength and small strain shear wave velocity were determined

for identical specimens formed by undercompaction method. It was found that silt content affects cyclic resistance and shear wave

velocity. In addition, the laboratory results indicated that using the existing field-based correlations will overestimate the cyclic

resistance of the Firoozkooh sand-silt mixtures when silt content is 60%. For clean sand and the specimens containing up to 30% fines,

results of this study on cyclic resistance are fairly consistent with Andrus and Stokoe correlations. These findings suggest the need for

further evaluation of the effects of non-plastic fines content upon liquefaction criteria derived from seismic field measurements.


Reza Abbasnia, Neda Mirzadeh, Kamyar Kildashti,
Volume 9, Issue 3 (9-2011)
Abstract

In recent years, different damage indexes have been introduced in engineering literature. The most prominent one among other

counterparts is the 1985 Park and Ang's damage index (DIPA), which demonstrates well calibration against experimental

results. Hence, it has traditionally had broad application in the field of structural engineering. Commonly, in DIPA relevant

parameters are assessed based on plastic-hinge approach, which is not well suited to consider the coupled response between

stress resultants (axial force and flexural moment) especially in grossly nonlinear domain. The reason is that named approach

is utilized constant shape plastic moment-curvature curve, which is not capable of varying the shape throughout loading history.

Another drawback of plastic-hinge method is the difficulty of representing precisely partial yielding of the cross-section. To

remedy the situation, the fiber discretization technique is used in this paper. Based on the fiber discretization strategy, not only

have the stiffness and strength degradation been characterized more accurately, but also the distribution of plasticity along the

plastic zone has been considered. Besides, the multi-directional effect of axial force and flexural moment is considered to assess

DI parameters. Additionally, this strategy directly incorporates the effect of transverse confinement into cross sectional

constitutive behaviour.


Kabir Sadeghi,
Volume 9, Issue 3 (9-2011)
Abstract

An energy based damage index based on a new nonlinear Finite element (FE) approach applicable to RC structures subjected to cyclic, earthquake or monotonic loading is proposed. The proposed method is based on the evaluation of nonlinear local degradation of materials and taking into account of the pseudo-plastic hinge produced in the critical sections of the structure. A computer program is developed, considering local behavior of confined and unconfined concretes and steel elements and also global behavior and damage of reinforced concrete structures under cyclic loading. The segments located between the pseudoplastic hinges at critical sections and the inflection points are selected as base-models through simulation by the proposed FE method. The proposed damage index is based on an energy analysis method considering the primary half-cycles energy absorbed by the structure during loading. The total primary half-cycles absorbed energy to failure is used as normalizing factor. By using the proposed nonlinear analytical approach, the structure's force-displacement data are determined. The damage index is then calculated and is compared with the allowable value. This damage index is an efficient means for deciding whether to repair or demolish structures after an earthquake. It is also useful in the design of new structures as a design parameter for an acceptable limit of damage defined by building codes.  The proposed approach and damage index are validated by results of tests carried out on reinforced concrete columns subjected to cyclic biaxial bending with axial force.


A. Hassanipour, A. Shafiee, M.k. Jafari,
Volume 9, Issue 4 (12-2011)
Abstract

Shear modulus and damping ratio are important input parameters in dynamic analysis. A series of resonant column tests was

carried out on pure clays and sand-clay mixtures prepared at different densities to investigate the effects of aggregate content,

confining stress, void ratio and clay plasticity on the maximum shear modulus and minimum damping ratio. Test results revealed

an increase in the maximum shear modulus of the mixture with the increase in sand content up to 60%, followed by a decrease

beyond this value. It was also found that the maximum shear modulus increases with confining stress, and decreases with void

ratio. In addition, minimum damping ratio increases with sand content and clay plasticity and decreases with confining stress.

Finally, on the basis of the test results, a mathematical model was developed for the maximum shear modulus.


A. Kaveh, O. Sabzi,
Volume 10, Issue 3 (9-2012)
Abstract

In this paper a discrete Big Bang-Big Crunch algorithm is applied to optimal design of reinforced concrete planar frames under

the gravity and lateral loads. Optimization is based on ACI 318-08 code. Columns are assumed to resist axial loads and bending

moments, while beams resist only bending moments. Second-order effects are also considered for the compression members, and

columns are checked for their slenderness and their end moments are magnified when necessary. The main aim of the BB-BC

process is to minimize the cost of material and construction of the reinforced concrete frames under the applied loads such that

the strength requirements of the ACI 318 code are fulfilled. In the process of optimization, the cost per unit length of the sections

is used for the formation of the subsequent generation. Three bending frames are optimized using BB-BC and the results are

compared to those of the genetic algorithm.


A. A. Maghsoudi, H. Akbarzadeh Bengar,
Volume 10, Issue 4 (12-2012)
Abstract

In order to lighten the prestressed concrete solid members, nowadays, it is possible to make use of the advantage of HPC (fc'>60

MPa) as well as replacing the solid section with a PSC thin-walled section for certain members such as circular and box columns.

Using the strength theory of ACI, a numerical procedure along with a computer program was developed for the analysis of such

sections subjected to axial compression or tension load and bending moments. The program solves for all possible variables such

as, concrete compressive strength (fc'= 60-100 MPa), type of prestressed steel, concrete cover, ratio of wall thickness to the section

dimensions and the PS steel arrangements to satisfy the given loading cases, thus leading to an optimal cost solution. However,

since the cross section is thin-walled circular or box and the PS steel is located at discrete points along the periphery of a circle

or rectangle, the equations of equilibrium are complex for hand computations (especially for circular section) but suitable for

computer program. So, by use of MATLAB software the interaction diagrams were also drawn for the analysis of such sections

for all mentioned variables. The use of prestressed thin-walled column diagrams is a safe and easy tool for the analysis of such

columns. Finally, the accuracy of the proposed method is demonstrated by comparing its results to those of the available

experimental values and is indicate that the proposed method predict very well the capacity of prestressed thin-walled column.


Seyed B. Beheshti-Aval,
Volume 10, Issue 4 (12-2012)
Abstract

A comparison between design codes i.e. ACI and AISC-LRFD in evaluation of flexural strength of concrete filled steel tubular

columns (CFTs) is examined. For this purpose an analytical study on the response of CFTs under axial-flexural loading is carried

using three-dimensional finite elements with elasto-plastic model for concrete with cracking and crushing capability and elastoplastic

kinematic hardening model for steel. The accuracy of the model is verified against previous test results. The nonlinear

modeling of CFT columns shows that the minimum thickness that recommended by ACI and AISC-LRFD to prevent local buckling

before the steel shell yielding for CFT columns could be decreased. The comparison of analytical results and codes indicates that

the accuracy of ACI method in estimation of axial-flexural strength of CFT columns is more appropriate than AISC-LRFD. The

ACI lateral strength of CFTs is located on upper bond of the AISC-LRFD’s provisions. AISC-LRFD estimates the lateral strength

conservatively but ACI in some ranges such as in short columns or under high axial load levels computes lateral strength in nonconservative

manner. Supplementary provisions for post local buckling strength of CFT columns should be incorporated in high

seismic region. This effect would be pronounced for column with high aspect ratio and short columns.


A. R. Rahai, S. Fallah Nafari,
Volume 11, Issue 4 (12-2013)
Abstract

The seismic behavior of frame bridges is generally evaluated using nonlinear static analysis with different plasticity models hence this paper tends to focus on the effectiveness of the two most common nonlinear modeling approaches comprising of concentrated and distributed plasticity models. A three-span prestressed concrete frame bridge in Tehran, Iran, including a pair of independent parallel bridge structures was selected as the model of the study. The parallel bridges were composed of identical decks with the total length of 215 meters supported on different regular and irregular substructures with non-prismatic piers. To calibrate the analytical modeling, a large-scale experimental and analytical seismic study on a two-span reinforced concrete bridge system carried out at the University of Nevada Reno was used. The comparison of the results shows the accuracy of analytical studies. In addition, close correlation between results obtained from two nonlinear modeling methods depicts that the lumped plasticity approach can be decisively considered as the useful tool for the nonlinear modeling of non-prismatic bridge piers with hollow sections due to its simple modeling assumption and less computational time.
H. Rahami, A. Kaveh, M. Ardalan Asl, S. R. Mirghaderi,
Volume 11, Issue 4 (12-2013)
Abstract

In the process of structural analysis we often come to structures that can be analyzed with simpler methods than the standard approaches. For these structures, known as regular structures, the matrices involved are in canonical forms and their eigen-solution can be performed in a simple manner. However, by adding or removing some elements or nodes, such methods cannot be utilized. Here, an efficient method is developed for the analysis of irregular structures in the form a regular structure with additional or missing nodes or with additional or missing supports. In this method, the saving in computational time is considerable. The power of the method becomes more apparent when the analysis should be repeated very many times as it is the case in optimal design or non-linear analysis.
H. Shakib, Gh. R. Atefatdoost,
Volume 12, Issue 1 (3-2014)
Abstract

An approach was formulated for the nonlinear analysis of three-dimensional dynamic soil-structure interaction (SSI) of asymmetric buildings in time domain in order to evaluate the seismic response behavior of torsionally coupled wall-type buildings. The asymmetric building was idealized as a single-storey three-dimensional system resting on different soil conditions. The soil beneath the superstructure was modeled as nonlinear solid element. As the stiffness of the reinforced concrete flexural wall is a strength dependent parameter, a method for strength distribution among the lateral force resisting elements was considered. The response of soil-structure interaction of the system under the lateral component of El Centro 1940 earthquake record was evaluated and the effect of base flexibility on the response behavior of the system was verified. The results indicated that the base flexibility decreased the torsional response of asymmetric building so that this effect for soft soil was maximum. On the other hand, the torsional effects can be minimized by using a strength distribution, when the centre of both strength CV and rigidity CR is located on the opposite side of the centre of mass CM, and SSI has no effect on this criterion.
M. Abbasi, A. H. Davaei Markazi,
Volume 12, Issue 1 (3-2014)
Abstract

An important factor in the design and implementation of structural control strategies is the number and placement of actuators. By employing optimally-located actuators, the effectiveness of control system increases, while with an optimal number of actuators, an acceptable level of performance can be achieved with fewer actuators. The method proposed in this paper, simultaneously determines the number and location of actuators, installed in a building, in an optimal sense. In particular, a genetic algorithm which minimizes a suitably defined structural damage index is introduced and applied to a well-known nonlinear model of a 20-story benchmark building. It is shown in the paper that an equal damage protection, compared to the work of other researchers, can be achieved with fewer numbers of optimally placed actuators. This result can be important from economic point of view. However, the attempt to minimize one performance index has negative effect on the others. To cope with this problem to some extent, the proposed genetic methodology has been modified to be applied in a multi-objective optimization problem.
A. Gholizad, P. Kamrani Moghaddam,
Volume 12, Issue 1 (3-2014)
Abstract

High performance and reliability of refurbish able knee braced steel frames has been confirmed in previous researches trying to get an optimal design for its configuration. Buckling of diagonal member which affects the hysteretic behavior of KBF under cyclic loadings has not been foreseen in previous evaluations of this system. This deficiency can be improved by utilization of adjustable rotary friction damper device (FDD) as knee element. Diagonal element buckling can be prevented considering a suitable value for FDD sliding threshold moment Mf. Lower values of Mf Lower energy dissipation rate in FDD and this leads to an optimization problem. Nonlinear time history analyses have been performed in addition to lateral cyclic loading analyses to evaluate the response of single story KBF subjected to seismic excitation. Optimal Mf in FDD has been chosen according to these analyses results. Roof displacement and acceleration, base shear and diagonal element’s buckling status have been compared in optimally designed KBF and FDD utilized KBF (FKBF) with different configurations. Nonlinear dynamic analyses have been performed for one, four, eight and twelve story frames under different seismic records with several PGAs. More than 60% displacement response reduction has been earned for the FKBF without considerable increase in base shear.
R. Vidjeapriya, V. Vasanthalakshmi, K. P. Jaya,
Volume 12, Issue 1 (3-2014)
Abstract

The present study focuses on the performance of precast concrete beam-column dowel connections subjected to cyclic loading by conducting experiments. In this study, one-third scale model of two types of precast and a monolithic beam-column connection were cast and tested under reverse cyclic loading. The precast connections considered for this study is a beam-column connection where beam is connected to column with corbel using (i) dowel bar and (ii) dowel bar with cleat angle. The experimental results of the precast specimens have been compared with that of the reference monolithic connection. The sub-assemblage specimens have been subjected to reverse cyclic displacement-controlled lateral loading applied at the end of the beam. The performance of the precast connections in terms of the ultimate load carrying capacity, post- elastic strength enhancement factor, load-displacement hysteresis behaviour, moment-rotation hysteresis behaviour, energy dissipation capacity, equivalent viscous damping ratio and ductility factor were compared with that of the monolithic beam-column connection. The monolithic specimen was found to perform better when compared to the precast specimens in terms of strength and energy dissipation. In terms of ductility, the precast specimen using dowel bar and cleat angle showed better behaviour when compared to the reference monolithic specimen.

Page 1 from 3    
First
Previous
1
 

© 2019 All Rights Reserved | International Journal of Civil Engineering

Designed & Developed by : Yektaweb