Search published articles


Showing 167 results for Cement

H.r. Ghafouri,
Volume 1, Issue 1 (9-2003)
Abstract

A two-dimensional mathematical model for the prediction of time-variations of river-bend displacements was developed which is particularly applicable to meandering rivers. The computational procedure consists of two stages, that is , in the first stage by utilizing depth-averaged continuity and momentum equations, velocity field as well as water surface profile in a river is determined. The well-known Finite-Element technique was applied to the governing equations. In the second stage the rate of river bank erosion is computed in terms of determined depths and velocities. The model utilizes Odgaards (1989) bank-erosion model in this stage. The procedure is then performed repeatedly over the entire time span in a staggered manner. The developed model was applied to simulate the migration of Qezel Ozan river. The fairly good match obtained indicates the applicability of the model.
Pakbaz M.c., Ahmadi C.,
Volume 1, Issue 2 (12-2003)
Abstract

This research include, more than 400 erosion tests performed on coarse and fine grain suspension materials. The purpose of tests was to determine erosion characteristics of mixtures of different materials. Samples of the .same constituents in different groups were cured tit two different setting time of // and 16 !tours before they were subjected to the constant hydraulic heads of 20 and 40 cm for ct time period of 30 urinates. The amount of erosion was measured as the weight loss of the samples offer the test. /n general the lower setting tune and the higher hydraulic head for a large group of samples showed higher erosion. For uniform sand samples when the cement content was 60-70 % the percentage of erosion (PE) was below 2. For the mixture of sand-cement, with the clay content below, 20% the percentage of erosion was below 2 and it increased to 15.5 for the clan, content of 58dc. Die addition of bentonite in the soil-cement mixtures in general did not affect the erosion.
Mazloom M., Ramezanian Pour A.a.,
Volume 2, Issue 1 (3-2004)
Abstract

This paper presents the long-term deformations of reinforced high-strength concrete columns subjected to constant sustained axial forces. The objective of the study was to investigate the effects of binder systems containing different levels of silica fume on time-dependent behaviour of high-strength concrete columns. The experimental part of the work focused on concrete mixes having a fixed water/binder ratio of 0.35 and a constant total binder content of 500 kg/m3. The percentages of silica fume that replaced cement in this research were: 0%, 6%, 8%, 10% and 15%. The mechanical properties evaluated in the laboratory were: compressive strength secant modulus of elasticity strain due to creep and shrinkage. The theoretical part of the work is about stress redistribution between concrete and steel reinforcement as a result of time-dependent behaviour of concrete. The technique used for including creep in the analysis of reinforced concrete columns was age-adjusted effective modulus method. The results of this research indicate that as the proportion of silica fume increased, the short-term mechanical properties of concrete such as 28-day compressive strength and secant modulus improved. Also the percentages of silica fume replacement did not have a significant influence on total shrinkage however, the autogenous shrinkage of concrete increased as the amount of silica fume increased. Moreover, the basic creep of concrete decreased at higher silica fume replacement levels. Drying creep (total creep - basic creep) was negligible in this investigation. The results of the theoretical part of this researchindicate that as the proportion of silica fume increased, the gradual transfer of load from the concrete to the reinforcement decreased and also the effect of steel bars in lowering the concrete deformation reduced. Moreover, the total strain of concrete columns decreased at higher silicafume replacement levels.
H. Ghiassian,
Volume 2, Issue 1 (3-2004)
Abstract

A study of bearing capacity and compressibility characteristics of cohesive soil, reinforced by geogrid and supporting square footing loads has been conducted. The lack of adequate frictional resistance between clay and reinforcing elements was compensated by using a thin sand layer (lens) encapsulating the geogrid sheet. In this way, tensile forces induced in the geogrid were transferred to the bulk clay medium through the sand particles and soil reinforcement was improved Experiments were conduced on two sets of specimens, one set of 1 x 1 x 1 m dimension and the footing size of 19 x 19 cm (series A), and the other set of 0.15 x 0.15 x 0.15 m dimension and the footing size of 3.7 x 3.7 cm (series B). The loading systems for the above specimens were stress controlled and strain controlled respectively. All specimens were saturated and presumably loaded under an undrained condition. The results qualitatively confirmed the effectiveness of the sand lens in improving the bearing capacity and settlement characteristics of the model footing. In series A, the maximum increase in the bearing capacity due to the presence of the sand lens was 17% whereas in series B, the amount of increase was 24%. The percentage reductions in the settlement for these results were 30% and 46% respectively.
Bakhtiari Nejad F., Rahai A., Esfandiari A.,
Volume 2, Issue 2 (6-2004)
Abstract

In this paper a structural damage detection algorithm using static test data is presented. Damage is considered as a reduction in the structural stiffness (Axial and/or Flexural) parameters. Change in the static displacement of a structure is characterized as a set of non-linear undetermined simultaneous equations that relates the changes in static response of the structure to the location and severity of damage. An optimality criterion is introduced to solve these equations by minimizing the difference between the load vector of damaged and undamaged structures. The overall formulation leads to a non-linear optimization problem with non-linear equality and linear inequality constraints. A method based on stored strain energy in elements is presented to select the loading location. Measurement locations are selected based on Fisher Information Matrix. Numerical and experimental results of a 2D frame represent good ability of this method in detecting damages in a given structure with presence of noise in measurements.
Ghodrati Amiri G., Sedighi S.,
Volume 2, Issue 4 (12-2004)
Abstract

In the past decade design procedure changed to �performance-based design� from�force-based design�, by this mean many researchers focused on nonlinear static analysis (NSA)and the procedure named �PUSHOVER�. Advantages of this method are defining the inelasticbehavior of structure without nonlinear dynamic analysis (NDA) effort and also defining plastichinges formation in critical elements, and the order of formed plastic hinges. In spite of these goodadvantages NSA is limited to short and planar structures and application of that in tall andtorsionaly asymmetric structures may yield unreliable results.In this study reliability of NSA is investigated by performing both nonlinear static and dynamicanalysis on six 2D moment resisting concrete frames. Non linear dynamic analysis has been doneby the suggested method in FEMA356 guideline called �Target Displacement Method�. A groupof 4 different lateral increasing loads were used in pushover analysis and 3 different groundmotions were applied in NDA. Results indicate that same responses can be obtained by performingNSA, but errors will be increased by frames height increment.
Soroush A., Koohi Sh.,
Volume 2, Issue 4 (12-2004)
Abstract

Lateral spreading of liquefied saturated sandy deposits happens during and shortly afterearthquakes. This paper first reviews this phenomenon by means of reviewing and comparingobservations on case histories and experimental works. Based on the results from the review andcomparison, a mechanism for describing lateral spreading will be suggested. The Finn model,adopted in the Computer code FLAC is employed to carry out numerical analyses of lateralspreading of the Wildlife Site, happened during the 1987 Superstition Hills earthquake. First themodel is calibrated by means of numerical analysis of the first centrifuge model test of theVELACS Project. For the Wildlife site, three types of analysis are carried out: a) coupledliquefaction-consolidation analysis using the coefficient of permeability (K1) of the liquefiedlayers, as reported in the literature b) analysis type (a), but with K equal to 0.1K1, and c) a fullyundrained liquefaction analysis. The analyses results, in forms of excess pore water pressures andsurface displacements, indicated that the fully undrained behavior of the liquefied layers betterrepresents the behavior and response of the site during the earthquake.
M. Naderi,
Volume 3, Issue 1 (3-2005)
Abstract

Having observed the costly failures of different cutoff walls, that had been constructed according to the mix design specified by reputable consultants in Iran, a research programme was conducted to study the effects of constituent materials on the properties of plastic concrete. The main properties, such as compressive strength, biaxial and triaxial strains, permeability, and modulus of elasticity have been investigated using different mixes, obtained from prototype production line plant, situated on site, because it was realized that the site production line and the systems employed have major effects on the properties of plastic concrete. Statistical analysis of the results, revealed the coefficients of influence of main constituent materials of plastic concrete namely cement, bentonite, aggregate and water on its compressive strength and modulus of elasticity. Having realized the cancelling effects of bentonite and aggregates on the measured properties, some equations relating the quantities of cement and water to the compressive strength and modulus of elasticity are introduced. Effects of clay and hydrated lime powder, as fillers were also investigated leading to the proposal of limits for their safe and economic use. Since most of the cutoff walls are buried structures, failure strains under both uniaxial and triaxial tests, with values of cohesion and internal friction, are also presented in this paper.
H. Salehzadeh, D.c. Procter, C.m. Merrifield,
Volume 4, Issue 1 (3-2006)
Abstract

Carbonate materials are mostly found in tropical areas, where exploiting gas and oil resources are of high concern. Their unique behavior under shear loading first was recognised during oil resources investigations in the Persian Gulf. Off-shore structures have been placed on carbonate soils which are highly crushable.During storms cyclic loading imposes on the bases of structures lied down on seabed. Cyclic loading, therefore, may trigger liquefaction phenomenon which leads to soil collapse and a catostrophic event. Therefore, stability of these expensive structures need to be investigated. To this aim carbonate sand in medium dense to medium dense state was considered and its response under varied cyclic shear stress ratio was studied.
A.r. Khoei, S. Yadegari, M. Anahid,
Volume 4, Issue 3 (9-2006)
Abstract

In this paper, a higher order continuum model is presented based on the Cosserat continuum theory in 3D numerical simulation of shear band localization. As the classical continuum models suffer from the pathological mesh-dependence in strain softening models, the governing equations are regularized by adding the rotational degrees-of-freedom to conventional degrees-of-freedom. The fundamental relations in three-dimensional Cosserat continuum are presented and the internal length parameters are introduced in the elasto-plastic constitutive matrix to control the shear bandwidth. Finally, the efficiency of proposed model and computational algorithm is demonstrated by a 3D strip in tensile. A comparison is performed between the classical and Cosserat theories and the effect of internal length parameter is demonstrated. Clearly, a finite shear bandwidth is achieved and the load-displacement curves are uniformly converged upon different mesh sizes.
F. R. Rofooei, N. K. Attari, A. Rasekh, A.h. Shodja,
Volume 4, Issue 3 (9-2006)
Abstract

Pushover analysis is a simplified nonlinear analysis technique that can be used to estimate the dynamic demands imposed on a structure under earthquake excitations. One of the first steps taken in this approximate solution is to assess the maximum roof displacement, known as target displacement, using the base shear versus roof displacement diagram. That could be done by the so-called dynamic pushover analysis, i.e. a dynamic time history analysis of an equivalent single degree of freedom model of the original system, as well as other available approximate static methods. In this paper, a number of load patterns, including a new approach, are considered to construct the related pushover curves. In a so-called dynamic pushover analysis, the bi-linear and tri-linear approximations of these pushover curves were used to assess the target displacements by performing dynamic nonlinear time history analyses. The results obtained for five different special moment resisting steel frames, using five earthquake records were compared with those resulted from the time history analysis of the original system. It is shown that the dynamic pushover analysis approach, specially, with the tri-linear approximation of the pushover curves, proves to have a better accuracy in assessing the target displacements. On the other hand, when nonlinear static procedure seems adequate, no specific preference is observed in using more complicated static procedures (proposed by codes) compared to the simple first mode target displacement assessment.
M. Mazloom, A.a. Mehrabian,
Volume 4, Issue 4 (12-2006)
Abstract

The objective of this paper is to present a new method for protecting the lives of residents in catastrophic earthquake failures of unreinforced masonry buildings by introducing some safe rooms within the buildings. The main idea is that occupants can seek refuge within the safe rooms as soon as the earthquake ground motions are felt. The information obtained from the historical ground motions happened in seismic zones around the globe expresses the lack of enough safety of masonry buildings against earthquake. For this potentially important reason, an attempt has been made to create some cost-effective seismic-resistant areas in some parts of the existing masonry buildings, which are called safe rooms. The practical method for creating these areas and increasing the occupant safety of the buildings is to install some prefabricated steel frames in some of their rooms or in their halls. These frames do not carry any service loads before earthquake. However, if a near field seismic event happens and the load bearing walls of the building destroy, some parts of its floors, which are in the safe areas, will fall on the roof of the installed frames consequently, the occupants who have sheltered in the safe rooms will survive. This paper expresses the experimental and theoretical work executed on the steel structures of the safe rooms for bearing the shock and impact loads. Finally, it was concluded that both the strength and displacement capacity of the steel frames were adequate to accommodate the distortions generated by seismic loads and aftershocks properly.
Ali Kheyroddin, Hosein Naderpour,
Volume 5, Issue 1 (3-2007)
Abstract

A parametric study is performed to assess the influence of the tension reinforcement index, ( ω = ρ fy /f Bc), and the bending moment distribution (loading type) on the ultimate deformation characteristics of reinforced concrete (RC) beams. The analytical results for 15 simply supported beams with different amounts of tension reinforcement ratio under three different loading conditions are presented and compared with the predictions of the various formulations and the experimental data, where available. The plastic hinge rotation capacity increases as the loading is changed from the concentrated load at the middle to the third-point loading, and it is a maximum for the case of the uniformly distributed load. The effect of the loading type on the plastic rotation capacity of the heavily reinforced beams is not as significant as that for the lightly reinforced beams. Based on the analytical results obtained using the nonlinear finite element method, new simple equations as a function of the tension reinforcement index, ω, and the loading type are proposed. The analytical results indicate that the proposed equations can be used for analysis of ultimate capacity and the associated deformations of RC beams with sufficient accuracy.
S.n. Moghaddas Tafreshi, Gh. Tavakoli Mehrjardi, S.m. Moghaddas Tafreshi,
Volume 5, Issue 2 (6-2007)
Abstract

The safety of buried pipes under repeated load has been a challenging task in geotechnical engineering. In this paper artificial neural network and regression model for predicting the vertical deformation of high-density polyethylene (HDPE), small diameter flexible pipes buried in reinforced trenches, which were subjected to repeated loadings to simulate the heavy vehicle loads, are proposed. The experimental data from tests show that the vertical diametric strain (VDS) of pipe embedded in reinforced sand depends on relative density of sand, number of reinforced layers and height of embedment depth of pipe significantly. Therefore in this investigation, the value of VDS is related to above pointed parameters. A database of 72 experiments from laboratory tests were utilized to train, validate and test the developed neural network and regression model. The results show that the predicted of the vertical diametric strain (VDS) using the trained neural network and regression model are in good agreement with the experimental results but the predictions obtained from the neural network are better than regression model as the maximum percentage of error for training data is less than 1.56% and 27.4%, for neural network and regression model, respectively. Also the additional set of 24 data was used for validation of the model as 90% of predicted results have less than 7% and 21.5% error for neural network and regression model, respectively. A parametric study has been conducted using the trained neural network to study the important parameters on the vertical diametric strain.
A.a. Maghsoudi, H. Akbarzadeh Bengar,
Volume 5, Issue 2 (6-2007)
Abstract

Limit to the tension reinforcement ratio ( ρ) in flexural high strength reinforced concrete (HSRC) members is based on the requirement that tension failure as sufficient rotation capacity are ensured at ultimate limit state. However, the provisions for the total amount of longitudinal reinforcement ratio ( ρ and ρ’) are not associated with any rational derivation. In this paper, a quantitative measure to evaluate an upper limit to the compression reinforcement ratio ρBmax of flexural HSRC members is proposed. The quantitative criterion to ρBmax can be derived from i) steel congestion and ii) considerations that are related to the diagonal compression bearing capacity of the members. In this paper it is shown that, when shear loading is dominant, the limit to is set by the diagonal compression criterion. Parameters that affect this limit are deeply investigated and the expressions were derived for different end conditions, to provide an additional tool for a better design and assessment of the flexural capacity of HSRC members.
H.r. Ashrafi, A.a. Ramezanianpour,
Volume 5, Issue 3 (9-2007)
Abstract

Deterioration of concrete structures in the Gulf region is a serious problem. Penetration of Chloride ion into concrete is responsible for such early deterioration. Determination of chloride diffusion coefficient is an effective way to predict the service life of concrete structures. In order to investigate the performance of concrete mixtures in such environments, ordinary and silica fume concrete mixtures containing various water to cementitious materials ratios were used. Rapid chloride permeability test and determination of diffusion coefficient of chloride ion penetration in accordance with bulk diffusion test under laboratory conditons simulated to Persian Gulf climate, and site investigation were performed. Concentration of chloride ions in various depths of concrete specimens was measured using acid soluble chloride test method. Test results show that silica fume reduces the chloride penetration and the diffusion coefficient in concrete mixtures. Different models were made for rapid chloride test results, and diffusion coefficient, of concretes maintained in the hot and corrosive environments of the Persian Gulf. The models which were calibrated with real data obtained from the concrete structures are capable to predict the penetration and service life of concrete structures in such corrosive environments.
H. Shakib, A. Ghasemi,
Volume 5, Issue 4 (12-2007)
Abstract

An attempt has been made to explore the general trends in the seismic response of planasymmetric structures when subjected to near-fault and far-fault ground motions. Systems with structural wall elements in both orthogonal directions considering actual and common nonlinear behavior under bi-directional excitation were studied. Idealized single-storey models with uni-axial eccentricity were employed. The main findings are: The rotational response trend considering actual behavior method would be different from common behavior method assumption, when the system subjected to near-fault motions. In the former case, the minimum rotational response could be achieved, when stiffness and strength centers are located on opposite side of the mass center. In the latter case, stiffness eccentricity determines the minimum and maximum rotational response. General trends in the rotational demand for far-fault motions, considering two type behavior assumptions, are similar to the last case. Moreover, in near-fault motions, when stiffness and strength centers are located on opposite side of the mass center, stiff side displacement demand would be greater than that soft side which is contrary to the conventional guidelines. While, in farfault motions similar to near-fault motions which stiffness and strength centers are located on one side of the mass center, displacement demand would be according to conventional guidelines.
P. Ghoddousi, A.m. Raiss Ghasemi, T. Parhizkar,
Volume 5, Issue 4 (12-2007)
Abstract

Plastic shrinkage is one of the most important parameter which must be considered in hot weather concreting. If plastic shrinkage is not prevented, cracking will be significant, especialy if silica fume is used in the mix. In this paper, the effect of silica fume in bleeding and evaporation was investigated in laboratory. The results showed that in restrained shrinkage, beside relative humidity, temperature and wind velocity, sun rediation also is very important factor in evaporation rate. It is found that under solar radition condition, the evaporation was much larger than the estimated value in ACI 305 Nomogram. The rate of evaporaion under solar radiation was about two folds of evaporation rate under shade condition. The results showed that in terms of crack initiation time, crack width and total cracking area, concrete containing silica fume is more severe than concrete with no silica fume. Reduction of water cement ratio in concrete with silica fume makes the concrete more sensitive in cracking. The results of this project also showed that the severity of the cracking is not related only to rate of bleeding but all environmental factors including like sun radiation or shading and also mix compositions have important roles.
S.n. Moghaddas Tafreshi, A. Asakereh,
Volume 5, Issue 4 (12-2007)
Abstract

Conventional investigations on the behavior of reinforced and unreinforced soils are often investigated at the failure point. In this paper, a new concept of comparison of the behavior of reinforced and unreinforced soil by estimating the strength and strength ratio (deviatoric stress of reinforced sample to unreinforced sample) at various strain levels is proposed. A comprehensive set of laboratory triaxial compression tests was carried out on wet (natural water content) non-plastic beach silty sand with and without geotextile. The layer configurations used are one, two, three and four horizontal reinforcing layers in a triaxial test sample. The influences of the number of geotextile layers and confining pressure at 3%, 6%, 9%, 12% and 15% of the imposed strain levels on sample were studied and described. The results show that the trend and magnitude of strength ratio is different for various strain level. It implies that using failure strength from peak point or strength corresponding to the axial-strain approximately 15% to evaluate the enhancement of strength or strength ratio due to reinforcement may cause hazard and uncertainty in practical design. Hence, it is necessary to consider the strength of reinforced sample compared with unreinforced sample at the imposed strain level. Only one type of soil and one type of geotextile were used in all tests.
Hon.m. Asce, M.r. Jalali, A. Afshar, M.a. Mariño,
Volume 5, Issue 4 (12-2007)
Abstract

Through a collection of cooperative agents called ants, the near optimal solution to the multi-reservoir operation problem may be effectively achieved employing Ant Colony Optimization Algorithms (ACOAs). The problem is approached by considering a finite operating horizon, classifying the possible releases from the reservoir(s) into pre-determined intervals, and projecting the problem on a graph. By defining an optimality criterion, the combination of desirable releases from the reservoirs or operating policy is determined. To minimize the possibility of premature convergence to a local optimum, a combination of Pheromone Re-Initiation (PRI) and Partial Path Replacement (PPR) mechanisms are presented and their effects have been tested in a benchmark, nonlinear, and multimodal mathematical function. The finalized model is then applied to develop an optimum operating policy for a single reservoir and a benchmark four-reservoir operation problem. Integration of these mechanisms improves the final result, as well as initial and final rate of convergence. In the benchmark Ackley function minimization problem, after 410 iterations, PRI mechanism improved the final solution by 97 percent and the combination of PRI and PPR mechanisms reduced final result to global optimum. As expected in the single-reservoir problem, with a continuous search space, a nonlinear programming (NLP) approach performed better than ACOAs employing a discretized search space on the decision variable (reservoir release). As the complexity of the system increases, the definition of an appropriate heuristic function becomes more and more difficult this may provide wrong initial sight or vision to the ants. By assigning a minimum weight to the exploitation term in a transition rule, the best result is obtained. In a benchmark 4-reservoir problem, a very low standard deviation is achieved for 10 different runs and it is considered as an indication of low diversity of the results. In 2 out of 10 runs, the global optimal solution is obtained, where in the other 8 runs results are as close as 99.8 percent of the global solution. Results and execution time compare well with those of well developed genetic algorithms (GAs).

Page 1 from 9    
First
Previous
1
 

© 2019 All Rights Reserved | International Journal of Civil Engineering

Designed & Developed by : Yektaweb