Search published articles


Showing 4 results for Silty Sands

Baziar M.h., Asna Ashari M.,
Volume 2, Issue 3 (9-2004)
Abstract

An experimental study was carried out to evaluate the liquefaction resistance of silty sand utilizing laboratory techniques. In this study, liquefaction potential of silty sand by using cyclic triaxial tests on frozen samples retrieved from calibration chamber and constructed samples by dry pouring method were investigated. Correlation between cone penetration resistance and cyclic strength of undisturbed silty sand samples are also examined using CPT calibration chamber and cyclic triaxial tests. The cone penetration tests were performed on silty sand samples with fine contents ranging from 0% to 50% and overburden stresses in the range of 100-300 kPa. Then the soil sample in calibration chamber, in the same way that soil samples were prepared during CPT sounding, was frozen and undisturbed soil specimen retrieved from frozen soil sample were tested using cyclic triaxial tests. Analysis of results indicates that the quality of frozen samples is affected by fine content and overburden pressures. Also, using data obtained in this research, the relationship between cone tip resistance and cyclic resistance ratio (CRR) for silty sand soils will be presented. These correlations are in relatively good agreement with field case history data. Also increasing confining pressure in silty sand material increases the cone tip resistance and generally, cyclic resistance ratio increases by increasing silt content.
S.a. Naeini, R. Ziaie-Moayed,
Volume 5, Issue 2 (6-2007)
Abstract

Series of undrained monotonic triaxial tests and cone penetration tests were conducted on loose silty sand samples to study correlation between undrained shear strength of silty sands (Sus) and piezocone test results. CPT tests were conducted at 27 silty sand samples in calibration chamber. The results indicate that, in low percent of silt (0-30%), as the silt content increases, the undrained shear strength (Sus) and cone tip resistance (qc) decreases. It is shown that, fines content affects undrained shear strength (Sus) and cone tip resistance (qc) similarly. On the basis of obtained results, equations were proposed to determine the normalized cone tip resistance (qc1n) and undrained shear strength (Sus) of silty sand in term of fines content. Finally based on those equations, a correlation between normalized cone tip resistance and undrained shear strength of silty sand is presented. It is shown that the normalized undrained shear strength and normalized cone tip resistance of loose silty sands (F.C. <30%) decreases with increase of silt contents.
Mohammad Hassan Baziar, Habib Shahnazari, Hassan Sharafi,
Volume 9, Issue 2 (6-2011)
Abstract

This paper discusses the applicability of a simple model to predict pore water pressure generation in non-plastic silty soil during

cyclic loading. Several Stress-controlled cyclic hollow torsional tests were conducted to directly measure excess pore water pressure

generation at different levels of cyclic stress ratios (CSR) for the specimens prepared with different silt contents (SC=0% to 100%).

The soil specimens were tested under three different confining pressures (&sigma'3= 60, 120, 240 kPa) at a constant relative density

(Dr=60%), with different silt contents. Results of these tests were used to investigate the behavior of silty sands under undrained

cyclic hollow torsional loading conditions. In general, beneficial effects of the silt were observed in the form of a decrease in excess

pore water pressure and an increase in the volumetric strain. Modified model for pore water pressure generation model based on

the test results are also presented in this paper. Comparison of the proposed pore pressure build up model with seed’s model

indicates the advantage of proposed model for soil with large amount of silt.


M. Alibolandi, Dr. R. Ziaie Moayed,
Volume 13, Issue 3 (12-2015)
Abstract

In this study a series of cyclic triaxial tests were performed to examine the undrained dynamic resistance of silty sand reinforced with various arrangements of geotextile layers. The silt content of samples varies in percentage from 0, 10, 20, 30, 40 and 50%. A total of 32 laboratory cyclic triaxial tests have been performed on silty sand samples reinforced with geotextile layers in different depths. All tests were performed with 100 kPa confining pressure, subjected to an isotropic consolidated undrained (CIU) condition. The tests were conducted at a frequency of 2 Hz. Results indicate that both the geotextile arrangement and the silt content were most essential in the liquefaction potential of reinforced sands. An increase in the number of geotextile layers enhanced the cyclic resistance of reinforced samples against the liquefaction potential. It was also found that when the geotextile layer was posited near the top of the specimen (load application part) the liquefaction resistance would increase (e.g. for clean sands, the improvement of liquefaction resistance caused by the geotextile layer had a 0.2 depth, and the sample height was 5.5 times greater than the geotextile layer inserted in mid height of sample H). Based on the obtained results, effects of geotextile on liquefaction resistance decreased as fines content increased to about 33%. Further increase in the fines content however, would lead to higher in reinforcement advantages. The liquefaction improvement is more effective with a higher number of geotextile layers. The results also revealed that the reinforcement effect in FC≈33 % is at its lowest amount. 



Page 1 from 1     

© 2019 All Rights Reserved | International Journal of Civil Engineering

Designed & Developed by : Yektaweb