Search published articles


Showing 12 results for Retaining Wall

A. Ghanbari, M. Ahmadabadi,
Volume 8, Issue 2 (6-2010)
Abstract

Inclined retaining walls with slopes less than perpendicular are appropriate candidates in several

engineering problems. Yet, to the knowledge of authors, only a few analytical solution for calculation of active earth

pressure on such walls, which will be usually smaller than the same pressure on vertical ones, has been presented

neither in research papers nor in design codes. Considering limit equilibrium concept in current research, a new

formulation is proposed for determination of active earth pressure, angle of failure wedge and application point of

resultant force for inclined walls. Necessary parameters are extracted assuming the pseudo-static seismic coefficient

to be valid in earthquake conditions. Moreover, based on Horizontal Slices Method (HSM) a new formulation is

obtained for determining the characteristics of inclined walls in granular and or frictional cohesive soils. Findings of

present analysis are then compared with results from other available methods in similar conditions and this way, the

validity of proposed methods has been proved. Finally according to the results of this research, a simplified relation

for considering the effect of slope in reduction of active earth pressure and change in failure wedge in inclined

retaining walls has been proposed.


A. Kaveh, A. Shakouri Mahmud Abadi,
Volume 9, Issue 1 (3-2011)
Abstract

Cost optimization of the reinforced concrete cantilever soil retaining wall of a given height satisfying some structural and geotechnical design constraints is performed utilizing harmony search and improved harmony search algorithms. The objective function considered is the cost of the structure, and design is based on ACI 318-05. This function is minimized subjected to design constraints. A numerical example of the cost optimization of a reinforced concrete cantilever retaining wall is presented to illustrate the performance of the presented algorithms and the necessary sensitivity analysis is performed.
A. Ghanbari, E. Hoomaan, M. Mojallal,
Volume 11, Issue 1 (5-2013)
Abstract

For calculating the natural frequency of structures such as buildings, chimneys, bridges and silos appropriate analytical

formulas exist. However, in the case of retaining walls undergoing the soil pressure at one side, calculating the natural frequency

is not a straightforward task and requires the effects of soil-structure interactions to be considered. By modeling the soil as series

of linear springs, a new formulation is presented in this article, to calculate the natural frequency of retaining walls. This formula

considers the vertical cross sectional width change, and hence, enables us to calculating the natural frequency of retaining walls

with different types of backfill. The geometrical properties of the retaining walls and its bending rigidity together with the soil’s

modulus of elasticity and its Poisson’s ratio are the most important parameters to calculate. A comparison of the results for

retaining walls with constant cross section obtained from the suggested method with those of the software analyses was carried

out and good agreement was detected. A second comparison of the results with those of other researchers revealed that the natural

frequency of flexible retaining wall is an upper bound for natural frequency of rigid walls. The Selected shape function is also

very close to the real shape mode.


J. Nazari Afshar, M. Ghazavi,
Volume 12, Issue 1 (1-2014)
Abstract

The Stone-column is a useful method for increasing the bearing capacity and reducing settlement of foundation soil. The prediction of accurate ultimate bearing capacity of stone columns is very important in soil improvement techniques. Bulging failure mechanism usually controls the failure mechanism. In this paper, an imaginary retaining wall is used such that it stretches vertically from the stone column edge. A simple analytical method is introduced for estimation of the ultimate bearing capacity of the stone column using Coulomb lateral earth pressure theory. Presented method needs conventional Mohr-coloumb shear strength parameters of the stone column material and the native soil for estimation the ultimate bearing capacity of stone column. The validity of the developed method has been verified using finite element method and test data. Parametric studies have been carried out and effects of contributing parameters such as stone column diameter, column spacing, and the internal friction angle of the stone column material on the ultimate bearing capacity have been investigated.
M. B. Esfandiari Sowmehsaraei, R. Jamshidi Chenari,
Volume 12, Issue 1 (1-2014)
Abstract

Soil reinforced with fiber shows characteristics of a composite material, in which fiber inclusion has a significant effect on soil permeability. Concerning to the higher void ratio of carpet fibers, at first stages it may be expected that an increase in fiber content of the reinforced soil would result in an increase in permeability of the mixture. However, the present article demonstrates that fiber inclusion will decrease the permeability of sand-fiber composite.A series of constant head permeability tests have been carried out to show the effects and consequently, a new system of phase relationships was introduced to calculate the dry mass for the sand portion of the composite. Monte Carlo simulation technique adopted with finite element theory was employed to back calculate the hydraulic conductivity of individual porous fibers from the laboratory test results. It was observed that the permeability coefficient of the porous fibers are orders of magnitude less than the skeletal sand portion due to the fine sand particle entrapment and also the fiber volume change characteristics.
C. Vieira,
Volume 12, Issue 1 (1-2014)
Abstract

This paper presents a simplified approach to estimate the resultant force, which should be provided by a retention system, for the equilibrium of unstable slopes. The results were obtained with a developed algorithm, based on limit equilibrium analyses, that assumes a two-part wedge failure mechanism. Design charts to obtain equivalent earth pressure coefficients are presented. Based on the results achieved with the developed computer code, an approximate equation to estimate the equivalent earth pressure coefficients is proposed. Given the slope angle, the backslope, the design friction angle, the height of the slope and the unit weight of the backfill, one can determine the resultant force for slope equilibrium. This simplified approach intends to provide an extension of the Coulomb earth pressure theory to the stability analyses of steep slopes and to broaden the available design charts for steep reinforced slopes with non-horizontal backslopes
S. N. Moghaddas Tafreshi, T. Nouri. A,
Volume 12, Issue 2 (4-2014)
Abstract

This paper presents a simple solution based on the limit equilibrium of sliding soil wedge of reinforced backfill subjected to the horizontal acceleration in the framework of the pseudo-static method. In particular, contrary to most studies on the reinforced retaining wall, the solution proposed in this study, takes into account the effect of the uniform surcharge on the reinforced backfill soil and of its distance from the face of the wall. The results are investigated in dimensionless form of the maximum reinforcement required strength (Kmax), the dimension of the sliding wedge (Lc/H), and the factor of safety (FS). Compared to the reinforced backfill without surcharge, the presence of surcharge over the reinforced backfill and of its distance from the top of the backfill have significant effects on the stability of the system. For a fixed surcharge, a minimum distance of surcharge exists for which the presence of the surcharge does not affect the solution and the failure mechanism is that corresponding to the case of system with no surcharge. A detailed design example is included to illustrate usage of proposed procedures. Comparisons of the present results with available results show a favorable agreement.
O. Farzaneh, F. Askari, J. Fatemi,
Volume 12, Issue 4 (12-2014)
Abstract

AWT IMAGEPresented is a method of two-dimensional analysis of the active earth pressure due to simultaneous effect of both soil weight and surcharge of strip foundation. The study’s aim is to provide a rigorous solution to the problem in the framework of upper-bound theorem of limit analysis method in order to produce some design charts for calculating the lateral active earth pressure of backfill when loaded by a strip foundation. A kinematically admissible collapse mechanism consisting of several rigid blocks with translational movement is considered in which energy dissipation takes place along planar velocity discontinuities. Comparing the lateral earth forces given by the present analysis with those of other researchers, it is shown that the results of present analysis are higher (better) than other researchers’ results. It was found that with the increase in AWT IMAGE, the proportion of the strip load (q) which is transmitted to the wall decreases. Moreover, Increasing the friction between soil and wall ( AWT IMAGE) will result in the increase of effective distance ( AWT IMAGE). Finally, these results are presented in the form of dimensionless design charts relating the mechanical characteristics of the soil, strip load conditions and active earth pressure.


M. Haghbin,
Volume 12, Issue 4 (12-2014)
Abstract

This research examines the behavior of soil-reinforced piles and applied loads based on the analytical method and by using the numerical results of FLAC3D software for comparison with the analytical results. The analysis was based on a method called virtual retaining wall, the following into consideration: an imaginary retaining wall that passes the footing edge the bearing capacity of footing on reinforced soil with piles, which was determined by applying equilibrium between active and passive forces on virtual wall and a pile row that exists beneath the shallow foundation. To calculate the lateral pile resistance here, an analytical equation was then required. The main objective of this paper is to determine the percentage of applied load on pile. Similarly, the effect of adding pile in various positions relative to the present footing (underpinning) was studied in this research. The various parameters of this study included pile length, vertical distance of pile head to shallow footing, pile distance to center of footing and location of the pile. Finally, the findings were compared with the numerical results of FLAC3D and the formerly presented experimental results. Results show that the analytical method, while being close to other methods is more conservative.


Amin Keshavarz, Mohsen Ebrahimi,
Volume 14, Issue 2 (3-2016)
Abstract

Lateral earth pressure on retaining walls is a widely researched classical problem in geotechnical engineering. This study investigates the active lateral earth pressure on a circular retaining wall using the stress characteristics method in the presence of soil-wall adhesion and friction. A computer code was developed for determining the lateral pressure of soil on the wall as well as the lateral pressure coefficients upon receiving the required input parameters. The principle of superposition was implemented to determine the lateral earth pressure coefficients. The effects of the soil-wall adhesion and friction angle on the lateral earth pressure were studied under active conditions. Moreover, the effects of these parameters on the characteristics network and failure region were demonstrated. The results showed that the coefficient of lateral earth pressure due to cohesion increased with increasing adhesion at the soil-wall boundary.


Maryam Haghbin,
Volume 14, Issue 7 (10-2016)
Abstract

In the present research, an analytical method is applied to determine the bearing capacity of strip footing on two layers of the soil. Bearing capacity of the footing is calculated according to soil resistance beneath the foundation and virtual retaining wall method. In the said method, the active and passive force on the retaining wall are considered equal on the edge in order to determine the bearing capacity of the footing. Regarding two layers of soil, the active and passive forces of each layer is found and their resultant is applied to calculate footing bearing capacity. This method has many advantages including the possibility to determine the depth of rupture surface of the soil beneath the footing, and to study the effect of the soil second layer on footing bearing capacity. Moreover, the effect of soil improvement beneath the footing as well as the depth and width of compacted area on bearing capacity of footing are also studied here in this research. In general, the studied parameters in this project consist of soil layers thickness, soil cohesion and friction angle, footing depth and width, the width of compacted soil beneath the footing, and the depth of underground water. By programming in MATLAB, the calculation and deduction was fulfilled. The results were compared with the bearing capacity of the footing on one layer of the soil in various situations in order to study the effect of various parameters in two layers of the soil. Finally, this bearing capacity of the footing was compared with the previous experimental methods and reliable results were obtained.


Alireza Darvishpour, Ali Ghanbari, Seyyed Ali Asghar Hosseini, Masoud Nekooei,
Volume 15, Issue 3 (5-2017)
Abstract

Most of the proposed methods for obtaining the free vibration natural frequency of the retaining wall have been presented, assuming the behavior of the wall in two-dimensional domain, and they are not able to express the three-dimensional behavior of these structures in a satisfying manner. In this paper, the plate theory is employed to analyze the free vibration of wall-soil system in three-dimensional domain. So the retaining wall is modeled as a clamped-free plate and the stiffness of the soil existing behind the wall is modeled as a set of springs. Using the approximate Rayleigh method, new analytical expression for obtaining the free vibration natural frequencies for the three first modes of the wall is represented. The results of the proposed model are compared with both the results of the other researchers and the ones from finite element method (FEM). They are also compared with the results of a full-scale experiment and it shows a good agreement. The comparison shows that modeling the wall in two-dimensional form is not accurate enough to calculate all the natural frequencies of the wall. The results of this paper show that there is a considerable difference between two- and three-dimensional behavior of the walls. The proposed method also gives the free vibration natural frequencies of the wall extensional modes with an acceptable accuracy. Finally, the effect of tensile and compressive behavior of the soil on the fundamental frequency is studied. This research can be considered as a new field in three-dimensional calculation of the retaining walls.



Page 1 from 1     

© 2019 All Rights Reserved | International Journal of Civil Engineering

Designed & Developed by : Yektaweb