Search published articles


Showing 13 results for Physical Model

Habib Shahnazari, Hosein Salehzadeh, Amin Askarinejad,
Volume 6, Issue 1 (3-2008)
Abstract

Classical soil mechanics involves the study of fully saturated soils. However, many problems encountered in geotechnical engineering practice involve unsaturated soil, in which behavior is significantly different from classical saturated soil. Negative pore pressure and capillary forces develop a virtual cohesion between the grains of semi saturated soils. This kind of cohesion is dependent on different factors such as grain size, saturation degree, soil-water characteristic curve and relative density of the soil. In this research the virtual cohesion of fine silty sand with 5% water content and a saturation degree of 17% is estimated. A vertical slope is constructed and is accelerated in the geotechnical centrifuge until failure. During the test, the model was monitored by a wireless video camera, attached to the strong box. The cohesionless tested sand was unsaturated. Based on the scaling laws and considering parameters such as sample unit weight, failure acceleration and the sample dimensions, a slope stability analysis was performed, and the virtual cohesion generated in the sample was calculated. The factor of safety of the prototype modeled in the centrifuge is calculated either by Finite Element Method and Finite Difference Method by using the resulted virtual cohesion from physical modeling. Results of this research show the validity of physical modeling for calculating the virtual cohesion in unsaturated silty sand.
Mohammad Reza Kavian Pour, H.r. Masoumi ,
Volume 6, Issue 3 (9-2008)
Abstract

Hydraulics of stepped spillway is a very complicated phenomenon, as it consists of a two phase flow passing through a set of designed steps. The steps increase the rate of energy dissipation taking place on the spillway face. Turbulence, flow aeration and energy dissipation are the main tasks in the design of such structures. This study consists of the experimental investigation to determine the energy dissipation over stepped spillways. Experiments conducted at Water Research Institute on two physical models of the Siyah Bisheh stepped spillways in Iran. To develop a more generalized expression, the results of previous investigations were also considered in our study. Therefore, a wide range of variables were taken into account to estimate the energy dissipation along the non-uniform flow regime. Assuming the energy dissipation along the uniform flow regime to be equal to the vertical displacement of the jet, the total energy lost was calculated. A comparison of the results with those of measurements showed a regression of 0.92 for the total energy dissipation, which is one of the features of the present method for estimating of the energy dissipation, compared with the previous investigation.
M.h. Baziar, A. Ghorbani, R. Katzenbach,
Volume 7, Issue 3 (9-2009)
Abstract

The pile-raft foundation is a combination of a raft foundation with piles. Pile-raft foundation has been widely designed, assuming all structure loads to be transferred to piles without considering contribution of the load taken by contact surface between raft and soil. Methods of analysis currently used in practice are based upon relatively conservative assumptions of soil behavior or on the less realistic soil-structure interaction. In this study the bearing -settlement behavior of combined pile-raft foundations on medium dense sand was investigated. 1g physical model test was performed on a circular rigid raft underpinned with four model piles. Numerical simulation was also carried out on the model test, using FLAC-3D, to show compatibility of the numerical analysis with the test. The obtained results showed very good accuracy of the numerical method used in this study as long as the applied load does not exceed the working load, while the performance of numerical model was relatively good for the loads beyond working load.
S.m. Moosavi, M.k. Jafari , M. Kamalian, A. Shafiee ,
Volume 8, Issue 2 (6-2010)
Abstract

Ground differential movements due to faulting have been observed to cause damage to engineered structures

and facilities. Although surface fault rupture is not a new problem, there are only a few building codes in the world

containing some type of provisions for reducing the risks. Fault setbacks or avoidance of construction in the proximity

to seismically active faults, are usually supposed as the first priority. In this paper, based on some 1-g physical

modelling tests, clear perspectives of surface fault rupture propagation and its interaction with shallow rigid

foundations are presented. It is observed that the surface fault rupture could be diverted by massive structures seated

on thick soil deposits. Where possible the fault has been deviated by the presence of the rigid foundation, which

remained undisturbed on the footwall. It is shown that the setback provision does not give generally enough assurance

that future faulting would not threaten the existing structures.


Y.y. Chang, C.j. Lee, W.c. Huang, W.j. Huang, M.l. Lin, W.y. Hung, Y. H. Lin,
Volume 11, Issue 2 (11-2013)
Abstract

This study presents a series of physical model tests and numerical simulations using PFC2D (both with a dip slip angle=60° and

a soil bed thickness of 0.2 m in model scale)at the acceleration conditions of 1g, 40g, and 80 g to model reverse faulting. The soil

deposits in prototype scale have thicknesses of 0.2 m, 8 m, and 16 m, respectively. This study also investigates the evolution of a

surface deformation profile and the propagation of subsurface rupture traces through overlying sand. This study proposes a

methodology for calibrating the micromechanical material parameters used in the numerical simulation based on the measured

surface settlements of the tested sand bed in the self-weight consolidation stage. The test results show that steeper surface slope

on the surface deformation profile, a wider shear band on the major faulting-induced distortion zone, and more faulting appeared

in the shallower depths in the 1-g reverse faulting model test than in the tests involving higher-g levels. The surface deformation

profile measured from the higher-g physical modeling and that calculated from numerical modeling show good agreement. The

width of the shear band obtained from the numerical simulation was slightly wider than that from the physical modeling at the

same g-levels and the position of the shear band moved an offset of 15 mm in model scale to the footwall compared with the results

of physical modeling.


H. Ghiassian, M. Jalili, I. Rahmani, Seyed M. M. Madani,
Volume 11, Issue 4 (12-2013)
Abstract

The concept of Geosynthetic Cellular Systems (GCS) has recently emerged as a new method in construction of breakwaters and coastal protective structures. The method potentially has significant advantages compared to conventional systems from the standpoint of constructability, cost effectiveness, and environmental considerations. This paper presents the results of physical model testing on the hydraulic responses of GCS structures under wave action. A series of model tests were carried out in a wave flume on GCS models with different shapes and soil types, subjected to various wave characteristics. Horizontal wave forces acting on the models were measured at different elevations. The maximum horizontal force in each test was calculated and compared with conventional formula of predicting wave pressure on breakwaters. The results show that Goda’s equation overestimates the hydrodynamic water pressure on these structures. This can be attributed to the influence of seeping water through the GCS models because of relative permeability of the GCS.
J. Nazari Afshar, M. Ghazavi,
Volume 12, Issue 1 (1-2014)
Abstract

The Stone-column is a useful method for increasing the bearing capacity and reducing settlement of foundation soil. The prediction of accurate ultimate bearing capacity of stone columns is very important in soil improvement techniques. Bulging failure mechanism usually controls the failure mechanism. In this paper, an imaginary retaining wall is used such that it stretches vertically from the stone column edge. A simple analytical method is introduced for estimation of the ultimate bearing capacity of the stone column using Coulomb lateral earth pressure theory. Presented method needs conventional Mohr-coloumb shear strength parameters of the stone column material and the native soil for estimation the ultimate bearing capacity of stone column. The validity of the developed method has been verified using finite element method and test data. Parametric studies have been carried out and effects of contributing parameters such as stone column diameter, column spacing, and the internal friction angle of the stone column material on the ultimate bearing capacity have been investigated.
M. Zare, A. Eslami,
Volume 12, Issue 4 (12-2014)
Abstract

Physical modeling for study of deep foundations can be performed in simple chambers (1g), calibration chambers (CC),

and centrifuge apparatus (ng). These common apparatus face certain limitations and difficulties. Recently, Frustum Confining

Vessels (FCV) have been evolved for physical modeling of deep foundations and penetrometers. Shaped as the frustum of a

cone, this device applies steady pressure on its bottom and creates a linear stress distribution along its vertical central core.

This paper presents the key findings in FCV, as developed in AUT. The FCV has a height of 1200 mm, with top and bottom

diameters of 300 and 1300 mm, respectively. By applying bottom pressure up to 600 kPa, the in-situ overburden stress

conditions, equivalent up to 40 m soil deposits, become consistent with the embedment depth of commonly used piles.

Observations indicated that a linear trend of stress distribution exists, and this device can create overburden stress in the

desired control volume along the central core. Moreover, a couple of compressive and tensile load tests were performed on

steel model piles driven in sand with a length of 750 mm, and different length to diameter (L/D) ratios between 8-15.

Comparison between measured and predicted ultimate capacity of model piles performed in FCV demonstrate a suitable

conformity for similar confinement conditions in the field. Therefore, the FCV can be considered as an appropriate approach

for the investigation of piling geotechnical behavior, and the examination of construction effects.


O. Nazari, E. Jabbari, H. Sarkardeh,
Volume 13, Issue 1 (3-2015)
Abstract

To dissipate energy and invert excessive discharge flow away from high dams into plunge pool, flip buckets are commonly designed and optimized by hydraulic model studies. In the present study, performance of chute flip buckets in different hydraulic and geometry conditions was investigated using experimental data of five different physical models. The collected experimental data such as Froude number, radius of flip bucket and slope of chute covered a wide range of chute flip buckets in prototype. By analyzing the data, relations for dynamic values of maximum and minimum pressures and their location along the flip bucket were extracted. Moreover, pressure distribution along the central axis of flip bucket was defined. Finally, results of the present research were compared with that of the other researches. Results of this study could be used in the design of chute flip buckets in hydraulic engineering.
Fatemeh Kazemi, Dr Saeed Reza Khodashenas, Hamed Sarkardeh,
Volume 14, Issue 1 (1-2016)
Abstract

Stilling basins dissipate energy in order to form hydraulic jumps and rotational flows. Hydraulic jump and rotational current phenomenon produces pressure fluctuation at the bottom of stilling basins. In the present study, pressure fluctuations and their locations have been studied in a physical model of Nimrod Dam. Results showed that fluctuations in presence of jump in the basin are high and therefore the fluctuation factors are respectively high. Regarding available empirical equations, the thickness of slab for different hydraulic conditions were calculated and compared in 1D and 2D conditions. By analyzing collected data, it was observed that, results of 1D were underestimated in comparison by 2D calculations.


Shuai Li, Jian-Min Zhang, Wei-Lin Xu, Jian-Gang Chen, Yong Peng, Jun-Ning Li, Xiao-Long He,
Volume 14, Issue 1 (1-2016)
Abstract

The cavitation erosion induced by high flow velocities is very prominent in high head and large unit discharge tunnel. Air entrainment is an effective technology to solve this problem. In this study, numerical simulation and physical model test are applied to the comparative study of air-water flows on bottom and lateral aerator in tunnel. The flow pattern, aeration cavity, air concentration and pressure distribution were obtained and there is a close agreement between the numerical and physical model values. The hydraulic characteristic and aeration effect of anti-arc section are analyzed. The results indicated that added lateral aeration facilities on 1# and 2# aerator can weaken backwater and increase the length of the bottom cavity, but it is limited to improve the air concentration and protect sidewall downstream of the ogee section. Air concentration improved on side walls downstream of anti-arc section when added lateral aeration facility on 3# aerator. The black water triangle zone disappeared and the floor and side walls well protected.


Yones Sojodi,
Volume 14, Issue 4 (6-2016)
Abstract

The paper present the results of various experimental and numerical studies on slopes, small scale physical modeling of slope under surcharge load were performed in loose sand environment. Digital images were captured during the incremental loading from side of model simultaneously. The Particle Image Velocimetry (PIV) and 3D numerical model was applied to investigate the slope under surcharge loading and some of the other important factors that control the performance of piles are investigated. The factors of safety and location of critical failure surfaces of reinforced and unreinforced slopes obtained and compared for various slopes. For homogenous slope, it is found for stabilized slope with piles, the 3D failure surface shape in front of piles is triangle, unlike its conical shape in laterally loaded piles. The paper also studies numerically the effect of soft bound effect, soil properties, pile spacing, pile position and surcharge distance effects on stabilized and none stabilized slopes. The results indicate that the depth of soft soil layer from ground surface and its angles with horizontal direction has importance effect on optimum location of stabilized pile. Studies on pile space effects shows with increasing pile space, arching phenomenon didn’t developed and partial pressure of supported portion transferred to un supported soil portion and the potential failure volume of the slope becomes large.



Volume 15, Issue 6 (9-2017)
Abstract

In this study, an assessment to excess pore water pressure generated around a single pile and pile group excited by two opposite rotary machines embedded in saturated sandy soil was considered experimentally. A small-scale physical model was manufactured to accomplish the experimental work in the laboratory. The physical model consists of: two small motors supplied with eccentric mass of 0.012 kg and eccentric distance (20 mm) representing the two opposite rotary machines, an aluminum shaft 20 mm in diameter as the pile, and a steel plate with dimensions of (160 × 160 × 20 mm) as a pile cap. The experimental work was achieved taking the following parameters into considerations: pile embedment depth ratio (L/d), spacing between piles (S) and operating frequency of the rotary machines. Twelve tests were conducted in medium dense fine sandy soil with 60 % relative density. In all these tests, the change in excess pore water pressure was measured around the pile at two spots: at the middle of the pile and at its tip. The results revealed that the generation of excess pore water pressure was affected by the following parameters: slenderness ratio of the pile, operating frequency of the machines, and the soil permeability. However, for all cases, it was found that the pore water pressure generated during operation was not greater than 20 % of the initial hydrostatic pressure. Using pile foundation reduced the amplitude of vertical vibration by about (300 %) for all operating frequencies, lengths of piles, pile spacings and number of piles. In addition, the presence of piles reduced the disturbance (fluctuation) in this amplitude by about (400 %). For single pile, and under the same operating frequency, a small decrease in the amplitude of vertical vibration resulted from increasing the length of the pile.



Page 1 from 1     

© 2019 All Rights Reserved | International Journal of Civil Engineering

Designed & Developed by : Yektaweb