Search published articles


Showing 9 results for Crushing

Saleh Zadeh H., Ghazanfari E.,
Volume 2, Issue 4 (12-2004)
Abstract

To study the behavior of carbonate sands parametrically, some monotonic triaxial testswere carried out on Kish carbonate sand. The sample was provided from Kish Island beach. Inorder to examine the effect of density and confining pressure, samples in loose and dense stateswere tested under different confining pressures. For studying the effect of drainage andconsolidation, different stress paths were followed. Also to study the effect of particle crushing indrained tests all samples were graded before and after testing. Comparison between loose anddense samples in both drained and undrained tests showed that with increasing confiningpressure, the reduction in shear resistance in loose samples is less than dense samples and theincrement rate of particle crushing in loose samples is more than dense samples. In the range oflow confining pressures both loose and dense samples showed dilation response. With increasingconfining pressure, the loose samples tended to exhibit contraction and the rate of dilation indense samples reduced. Because recovering undisturbed sample of carbonate sediments is veryhard or even impossible so the effect of soil disturbance is not studied in this research.
Saleh Zadeh H., Procter D.c., Merrifield C.m.,
Volume 3, Issue 3 (9-2005)
Abstract

The unique behaviour of carbonate materials under shear loading has stimulated in investigating of their geological and engineering properties.Carbonate soils composed of calcium or other carbonates and most abundant in tropical marine environments are of interest from geotechnical view, especially for offshore engineers engaged with Fossil-based fuel exploitation. This was initiated in the early 1960's, when the first offshore borings in the Persian Gulf identified layers of calcarenite and thick layers of sand containing visible shell fragments.For the purpose of exploiting gas and oil resources in hot and temperate climates (e.g. Persian Gulf) off-shore structures have been placed on carbonate soils. The carbonate sediments are high crushable compared with low crushable sediments such as quartzic soils.To examine the crushability of these problematic sediments a series of monotonic compression, extension and post-cyclic triaxial tests under different densities and confining pressures was carried out to study the crushing behaviour of "Rock" carbonate sand obtained from Cornwall, England.It was shown that crushing coefficient decreases with increasing in maximum principal effective stress ratio for both loose and dense states. It seems that for skeletal carbonate sand maximum and minimum dry densities will be changed during shearing loading. In other words, even though the sample has experienced an increase in density, it may also have experienced a reduction in relative density.
Mahmoud Hassanlourad, Hosein Salehzadeh, Habib Shahnazari,
Volume 6, Issue 2 (6-2008)
Abstract

In this paper shear behavior of two calcareous sands having different physical properties are

investigated using drained and undrained triaxial tests. The investigated sands are obtained from two different

zones located in Persian Gulf, Kish Island and Tonbak region. Analysis based on energy aspects show that

friction angle in these soils, having crushable particles, is formed of three components: substantial internal

friction angle, dilation and particle breakage angle. Dilation component is available in the two investigated

sand. Particle breakage component is a function of grains hardness, structure and geometry shape. Particles

breakage decreases the volume of sample during drained tests and creates positive pore water pressure during

undrained tests. Two investigated sands show different amount of dilation and particle breakage under similar

conditions. Simultaneous dilation and particles crushing and different amount of them result in different shear

behavior of the two studied sands. Energy aspects are used to determine the effect of particle crushing on the

shear strength. There is a suitable compatibility between relative breakage of grains and consumed energy

ratio for particle breakage.


A. Hamidi, M. Alizadeh, S.m. Soleimani,
Volume 7, Issue 1 (3-2009)
Abstract

There are limitations in experimental studies on sand-gravel mixtures due to the small size of testing

specimens. Due to this problem, many researchers have worked on prediction of the shear strength of mixture by testing

the sandy fraction of soil alone and developed empirical relationships. Most of the previous relationships have been

determined for low surcharge pressures in which particle breakage does not affect the shear strength parameters.

However, the particle breakage affects the relationships in higher confinements. At the present study, the results of

large scale direct shear tests on sand and sand-gravel mixtures was used to investigate the shear behavior and

dilatancy characteristics in a wider range of surcharge pressures. The gravel content, relative density, surcharge

pressure and gravel grain size were considered as variables in testing program. The relationships between shear

strength characteristics of sand and sand-gravel mixtures were determined considering dilation characteristics of the

soil. In this regard, the minimum void ratio was found as a useful indirect index that relates uniquely to the critical

state friction angle independent of soil gradation. The relations between critical state or peak friction angles of the

mixture with minimum void ratio were determined as a function of surcharge pressure. The correlations could be useful

for determination of the strength parameters of sand-gravel composites by testing sandy fraction of mixture.


Seyed B. Beheshti-Aval,
Volume 10, Issue 4 (12-2012)
Abstract

A comparison between design codes i.e. ACI and AISC-LRFD in evaluation of flexural strength of concrete filled steel tubular

columns (CFTs) is examined. For this purpose an analytical study on the response of CFTs under axial-flexural loading is carried

using three-dimensional finite elements with elasto-plastic model for concrete with cracking and crushing capability and elastoplastic

kinematic hardening model for steel. The accuracy of the model is verified against previous test results. The nonlinear

modeling of CFT columns shows that the minimum thickness that recommended by ACI and AISC-LRFD to prevent local buckling

before the steel shell yielding for CFT columns could be decreased. The comparison of analytical results and codes indicates that

the accuracy of ACI method in estimation of axial-flexural strength of CFT columns is more appropriate than AISC-LRFD. The

ACI lateral strength of CFTs is located on upper bond of the AISC-LRFD’s provisions. AISC-LRFD estimates the lateral strength

conservatively but ACI in some ranges such as in short columns or under high axial load levels computes lateral strength in nonconservative

manner. Supplementary provisions for post local buckling strength of CFT columns should be incorporated in high

seismic region. This effect would be pronounced for column with high aspect ratio and short columns.


A. R. Rahai, S. Fallah Nafari,
Volume 11, Issue 4 (12-2013)
Abstract

The seismic behavior of frame bridges is generally evaluated using nonlinear static analysis with different plasticity models hence this paper tends to focus on the effectiveness of the two most common nonlinear modeling approaches comprising of concentrated and distributed plasticity models. A three-span prestressed concrete frame bridge in Tehran, Iran, including a pair of independent parallel bridge structures was selected as the model of the study. The parallel bridges were composed of identical decks with the total length of 215 meters supported on different regular and irregular substructures with non-prismatic piers. To calibrate the analytical modeling, a large-scale experimental and analytical seismic study on a two-span reinforced concrete bridge system carried out at the University of Nevada Reno was used. The comparison of the results shows the accuracy of analytical studies. In addition, close correlation between results obtained from two nonlinear modeling methods depicts that the lumped plasticity approach can be decisively considered as the useful tool for the nonlinear modeling of non-prismatic bridge piers with hollow sections due to its simple modeling assumption and less computational time.
Farzin Kalantary, Javad Sadoghi Yazdi, Hossein Bazazzadeh,
Volume 12, Issue 3 (7-2014)
Abstract

In comparison with other geomaterials, constitutive modeling of rockfill materials and its validation is more complicated. This is principally due to the existence of more intricate phenomena such as particle crushing, as well as laboratory test limitations. These issues have necessitated developing more complex constitutive models, with many parameters. Regardless of the type of model, the calibrations of the parameters in such models are considered as one of the most important and challenging steps in the application of the model. Therefore, the need for comprehensive and rapid methods for evaluation of optimum parameters of the models is deemed necessary. In this paper, a Neuro-Fuzzy model in conjunction with Particle Swarm Optimization (PSO) is used for calibration of the twelve parameters of Hierarchical Single Surface (HISS) constitutive model based on the Disturbed State Concept (DSC). The Neuro-fuzzy system is used to provide a high-degree nonlinear regression model between the deviatoric stress and volumetric strain versus axial strain that has been obtained from consolidated drained large scale tri-axial tests on rockfill materials. The model parameters are determined in an iterative optimized loop with PSO and ANFIS such that the equations of DSC/HISS are simultaneously satisfied. Material data used in this study are gathered from the results of large tri-axial tests for two rockfill dams in Iran. It is shown that the proposed method has higher accuracy and more importantly its robustness is exhibited through test predictions. The achieved improvement is substantiated in a comparison with the more widely used "Least-Square" method.
S.h.r. Kargar, H. Shahnazari, H. Salehzadeh,
Volume 12, Issue 4 (12-2014)
Abstract

In this study, a researching program is conducted by cyclic triaxial test to determine the post-cyclic behavior of Bushehr carbonate sand retrieved from the north of the Persian Gulf, under anisotropic consolidation at 200 kPa confining pressure. The article compares the post-cyclic monotonic strength and excess pore water pressures generated after the test with the pre-cyclic monotonic results. The results attest to the existence of a relationship between CSR (Cyclic Stress Ratio) and the frequency of failure cycles. The article also investigates the relationship between the amount of excess pore pressures generated during both the cyclic and post-cyclic loading, revealing an increase in the post-cyclic strength and stiffness of sand retrieved from Bushehr. Also the effect of multi stages cyclic loading, density, pore pressure and stain history in post cyclic strength and stiffness is evaluated. The increasing in post cyclic strength and stiffness depends on excess pore pressure generated during cyclic loading and stain history. This article also reveals that a distinct trend in the relation between post cyclic behavior and crushing value does not exist at lower confining pressure.


A.r. Sattarifar, M.k. Sharbatdar, A. Dalvand,
Volume 13, Issue 4 (12-2015)
Abstract

In this paper, an experimental study has been conducted on strengthening of reinforced concrete (RC) connections by FRP sheets. The innovation of this research is using narrow grooves on critical regions of connection to increase the adherence of FRP sheets and prevent their early debonding. Therefore, four RC connections were made and tested under a constant axial load on the column and an increasing cyclic load on the beam. The first specimen, as the standard reference specimen, had close tie spacing in ductile regions of beam, column and panel zone based on seismic design provisions, and the second specimen, as the weak reference specimen did not have these conditions in all regions. Two other weak specimens were strengthened using two different strengthening patterns with FRP sheets one by ordinary surface preparation and the other with surface grooving method for installing FRP sheets on the connection. The results showed that ultimate load and ductility of the weak specimen compared to standard specimen decreased 25% and 17%, respectively. The shear failure and concrete crushing were prevented in the ductile regions of the beam and panel zone in both strengthened specimens. Also, it was observed that early debonding of FRP sheets was prevented in the strengthened connection with grooving pattern and so had desirable ductility and bearing capacity similar to the standard specimen.



Page 1 from 1     

© 2019 All Rights Reserved | International Journal of Civil Engineering

Designed & Developed by : Yektaweb