Search published articles


Showing 10 results for Cpt

Baziar M.h., Ziaie Moayed R.,
Volume 1, Issue 1 (9-2003)
Abstract

An experimental study was carried out to evaluate the influence of silt content on cone penetration measurements and its implication for soil classification. The investigation includes twenty-seven peizocone tests in saturated salty sand samples, which had been prepared in a big rigid thick walled steel cylinder-testing chamber. The samples were prepared with several different silt contents ranging from 0 to 50 percent and were consolidated at three-overburden effective stresses including 100, 200 and 300 kPa. This study showed that, the amount of silt content in sand is an important parameter affecting CPT results. As the silt content increases, the cone tip resistance decreases. The recorded excess pore water pressure during sounding was increased with increasing silt content. It is also concluded that friction ratio, in general, increases with increasing silt content. The method presented by Robertson and Wride [25] and Olsen [17] to evaluate soil classification are also verified.
A.r. Khaloo, Molaee A.,
Volume 1, Issue 2 (12-2003)
Abstract

An experimental program was carried out to investigate the behavior of steel, fiber reinforced concrete (SFRC) under abrasion and cycles of freeze and them. Compression and flexural tests were also performed in order to reach a comprehensive conclusion of the response. In total, over 200 specimens were tested The test variables included two concrete strength., (i. e., 28 MPa as Normal Strength (NSFRC) and 42 MPa as Medium Strength (MSFRC)), four volumetric percentage of fibers (i.e., 0%, 0,5%, 1.0% and 1.5%) and two fiber lengths (i.e.. 25mm and 35rnrn).Cube specimens were tested according to ASTM C6661n-ocedrrre B using 100 cycles of freeze and thaw. The Los Angeles test method for testing aggregate was used to evaluate the abrasion resistance of SFRC.Test results of1VSFRCptesertted improvements up to 39% and 32 % in cylindrical and cubic compressive strength, respectively. and 88�o in modulus of rupture, 57% in resistance against abrasion based oil weight loss and 40% against compressive strength reduction due to freeze and thaw cycles. The corresponding improvements for MSFRC were 18%, 16%, 48%, 53% and 46% respectively.Increase in cocncrete strength from 28 Ala to 42 MPa provided higher freeze and thaw and abrasion resistance than addition of 1.5% of steel fibers to the normal strength concrete matrix.
Baziar M.h., Asna Ashari M.,
Volume 2, Issue 3 (9-2004)
Abstract

An experimental study was carried out to evaluate the liquefaction resistance of silty sand utilizing laboratory techniques. In this study, liquefaction potential of silty sand by using cyclic triaxial tests on frozen samples retrieved from calibration chamber and constructed samples by dry pouring method were investigated. Correlation between cone penetration resistance and cyclic strength of undisturbed silty sand samples are also examined using CPT calibration chamber and cyclic triaxial tests. The cone penetration tests were performed on silty sand samples with fine contents ranging from 0% to 50% and overburden stresses in the range of 100-300 kPa. Then the soil sample in calibration chamber, in the same way that soil samples were prepared during CPT sounding, was frozen and undisturbed soil specimen retrieved from frozen soil sample were tested using cyclic triaxial tests. Analysis of results indicates that the quality of frozen samples is affected by fine content and overburden pressures. Also, using data obtained in this research, the relationship between cone tip resistance and cyclic resistance ratio (CRR) for silty sand soils will be presented. These correlations are in relatively good agreement with field case history data. Also increasing confining pressure in silty sand material increases the cone tip resistance and generally, cyclic resistance ratio increases by increasing silt content.
M.h. Baziar, R. Ziaie_moayed,
Volume 4, Issue 2 (6-2006)
Abstract

This paper highlights the effect of silt content on cone tip resistance in loose silty sand. In this study, twenty-seven cone penetration tests are performed in saturated silty sand samples with several different silt contents ranging from 10 to 50 percent. The samples are consolidated at three overburden stresses including 100, 200 and 300 kPa. It is shown that, as the silt content increases, the cone tip resistance decreases. In high percent of silt (30-50%), the cone tip resistance decreases more gently compared with low percent of silt (0-30%). It is also concluded that the method proposed by Olsen (1997) for stress normalization of cone tip resistance compared with the Robertson and Wride (1998) method has better agreement with the obtained results. To evaluate liquefaction potential of loose silty sand, the method presented by Robertson and Wride (1998) is also studied. The results showed that the use of Robertson and Wride (1998) method to estimate the fine content from CPT data causes some uncertainty especially for high silt content (FC>30%).
S.a. Naeini, R. Ziaie-Moayed,
Volume 5, Issue 2 (6-2007)
Abstract

Series of undrained monotonic triaxial tests and cone penetration tests were conducted on loose silty sand samples to study correlation between undrained shear strength of silty sands (Sus) and piezocone test results. CPT tests were conducted at 27 silty sand samples in calibration chamber. The results indicate that, in low percent of silt (0-30%), as the silt content increases, the undrained shear strength (Sus) and cone tip resistance (qc) decreases. It is shown that, fines content affects undrained shear strength (Sus) and cone tip resistance (qc) similarly. On the basis of obtained results, equations were proposed to determine the normalized cone tip resistance (qc1n) and undrained shear strength (Sus) of silty sand in term of fines content. Finally based on those equations, a correlation between normalized cone tip resistance and undrained shear strength of silty sand is presented. It is shown that the normalized undrained shear strength and normalized cone tip resistance of loose silty sands (F.C. <30%) decreases with increase of silt contents.
S.m. Mir Mohammad Hosseini, A.a. Hajimohammadi, A. R. Hajimohammadi,
Volume 8, Issue 2 (6-2010)
Abstract

Seismic piezocone device (SCPTu) together with Resonant Column and Cyclic Triaxial test apparatus are

employed to measure small strain shear modulus (G0) of carbonate sandy and clayey soils of southern coasts of Iran.

A large area of southern regions of Iran is formed from clay, silt and sand. In this study, maximum shear modulus that

is derived from both field (by seismic piezocone) and laboratory (by Resonant Column and Cyclic Triaxial) tests on

soil samples from the southern region, indicated a meaningful effect of sample disturbance. Results show that in

laboratory tests, loose samples tend to become denser and therefore exhibit greater stiffness whereas dense samples

tend to become looser, showing a reduction in stiffness. According to the results of the present study, there are narrow

limits of soils shear moduli for which the laboratory tests and the field measurements yield approximately the same

amounts. This limit of shear moduli is about 30-50(MPa) for clay deposits and 70-100 (MPa) for sandy deposits. Since

the shear moduli of soils in small strains can also be computed from the shear wave velocity, also correlations based

on parameters derived from SCPTu test for shear wave velocity determination of sandy and clayey soils of the studied

area are presented. This study shows that shear wave velocity can be related to both corrected tip resistance and total

normal stress. The measurements of the damping ratio and shear module, because of a great disturbance of stiff

deposits during the sampling process and also due to considerable differences between the laboratory and field

results, by the laboratory approaches are not reliable and advised.


A. Eslami Kenarsari, R. Jamshidi Chenari, A. Eslami,
Volume 11, Issue 1 (5-2013)
Abstract

Among the different ways of in-situ soil investigation, cone penetration test data are selected to evaluate the spatial variability

of geomaterials and the scale of fluctuations is chosen to evaluate the correlation structure of CPT data. In this regard six case

studies in sandy materials from Australia, U.S.A. and Iraq are selected. Various techniques for the calculation of the scale of

fluctuation of geotechnical parameters are suggested in literature e.g. VXP, SAI, AMF, BLM and VRF without any preference or

privilege for any specific procedure. In order to isolate the stochastic portion of cone tip resistance, deterministic trend was first

removed by regression analysis. This study suggests that quadratic trend removal is more suitable for selected CPT data

soundings. The closeness of the estimated scale of fluctuation using different approaches is assessed too. Mean value of the scale

of fluctuation by five established methods ranges between 0.44 to 1.52 meter for six different cases and the coefficient of

variation for the scale of fluctuation calculated by these methods varies between 12 to 27 % showing that available established

methods produce almost compatible and comparable results.


A. Eslami, I. Tajvidi, M. Karimpour-Fard,
Volume 12, Issue 1 (1-2014)
Abstract

Three common approaches to determine the axial pile capacity based on static analysis and in-situ tests are presented, compared and evaluated. The Unified Pile Design (UPD), American Petroleum Institute (API) and a SPT based methods were chosen to be validated. The API is a common method to estimate the axial bearing capacity of piles in marine environments, where as the others are currently used by geotechnical engineers. Seventy pile load test records performed in the northern bank of Persian Gulf with SPT profile have been compiled for methods evaluation. In all cases, pile capacities were measured using full scale static compression and/or pull out loading tests. As the loading tests in some cases were in the format of proof test without reaching the plunging or ultimate bearing capacity, for interpretation the results, offset limit load criteria was employed. Three statistical and probability based approaches in the form of a systematic ranking, called Rank Index, RI, were utilized to evaluate the performance of predictive methods. Wasted Capacity Index (WCI) concept was also applied to validate the efficiency of current methods. The evaluations revealed that among these three predictive methods, the UPD is more accurate and cost effective than the others.
H. Shahnazari, M. A. Shahin, M. A. Tutunchian,
Volume 12, Issue 1 (1-2014)
Abstract

Due to the heterogeneous nature of granular soils and the involvement of many effective parameters in the geotechnical behavior of soil-foundation systems, the accurate prediction of shallow foundation settlements on cohesionless soils is a complex engineering problem. In this study, three new evolutionary-based techniques, including evolutionary polynomial regression (EPR), classical genetic programming (GP), and gene expression programming (GEP), are utilized to obtain more accurate predictive settlement models. The models are developed using a large databank of standard penetration test (SPT)-based case histories. The values obtained from the new models are compared with those of the most precise models that have been previously proposed by researchers. The results show that the new EPR and GP-based models are able to predict the foundation settlement on cohesionless soils under the described conditions with R2 values higher than 87%. The artificial neural networks (ANNs) and genetic programming (GP)-based models obtained from the literature, have R2 values of about 85% and 83%, respectively which are higher than 80% for the GEP-based model. A subsequent comprehensive parametric study is further carried out to evaluate the sensitivity of the foundation settlement to the effective input parameters. The comparison results prove that the new EPR and GP-based models are the most accurate models. In this study, the feasibility of the EPR, GP and GEP approaches in finding solutions for highly nonlinear problems such as settlement of shallow foundations on granular soils is also clearly illustrated. The developed models are quite simple and straightforward and can be used reliably for routine design practice.
R. Jamshidi Chenari, P. Pishgah ,
Volume 12, Issue 2 (4-2014)
Abstract

In this technical note, a methodology is introduced for reliability calculation of consolidation settlement based on cone penetration test (CPT) data. The present study considers inherent soil variability which influences consolidation settlements results. To proceed reliability analysis, the measured data of a sample corrected cone tip resistance (􀝍􀯧) is detrended using a quadratic trend and the residuals are assumed to be lognormally distributed random field. Realizations of 􀝍􀯧 is generated by using spatial variability of residuals including standard deviation and the scale of fluctuation. The quadratic trend and the generated residuals are then combined to correlate shear and bulk modulus as input consolidation properties for coupled analysis and subsequently consolidation settlement was calculated by using finite difference method adopted in Monte Carlo simulations. The results of reliability analysis are presented describing the range of possible settlements by considering characteristics of uncertainties involved at the particular site. Number of realizations rendering settlements smaller than the allowable settlement must be such that guarantee proper performance or acceptable reliability index.

Page 1 from 1     

© 2019 All Rights Reserved | International Journal of Civil Engineering

Designed & Developed by : Yektaweb