Search published articles


Showing 8 results for Shariatmadari

P. Alimohammadi, N. Shariatmadari, M.a. Abdoli, H. Ghiasinejad, A. Mansouri,
Volume 8, Issue 2 (6-2010)
Abstract

Hydrologic Evaluation of Landfill Performance (HELP) model is one of the most accepted tools to simulate

the hydrological attributes of landfills. Although some major deviations from real values has been reported about the

calculated results for leachate generation by HELP model but other researchers and/or engineers in practice have

used it in some places to estimate amount of leachate produced in the landfills. On the Other hand this model is

elaborated and mainly used in developed countries with the waste having low moisture content and also in climatic

conditions with high precipitation. This research investigated the applicability of the model in arid areas, by

construction of two 30m× 50m (effective horizontal length) test cells in Kahrizak landfill (longitude=51°, 20',

latitude= 35° 27' degrees), and monitoring the real leachate generation from each one. A set of field capacity and

saturated water conductivity tests were also performed to determine basic hydrologic properties of municipal waste

landfilled. A comparison was made between values calculated by HELP model and recorded values, shows that a

prediction of leachate on annual basis can be done by HELP model with acceptable accuracy but when the infiltration

of water to waste body increases due to leachate production, the model intents to underestimate water storage capacity

of the landfill, which lead to deviation of calculated values from real ones.


Nader Shariatmadari , Marzieh Salami, Mehran Karimpour Fard,
Volume 9, Issue 2 (June 2011)
Abstract

The main task in the design and construction of impermeable liners in landfills is to block the migration of pollutants to the groundwater

systems or to reduce its rate to a reasonable amount. That is why environmental regulations force governments to construct engineered

waste dumps for waste management purposes. These liners are exposed to various types of chemical, biological, and physical processes

and are affected by the leachate which is produced from decomposition of waste materials accompanying methane gas. The leachate

includes a lot of components such as water and different types of salts. For this reason, the geotechnical characteristics of clay liners

which are evaluated in laboratories using distilled water or tap water might be far different from the representative sample of the in-situ

conditions. There are some evidences regarding the effect of these salts on the physical and mechanical properties of clay barriers which

could affect the long-term performance of these liners. Since the main criterion for impermeable bottom liners in landfills is their

hydraulics conductivity, the increase of this parameter could have a considerable environmental impact. This paper embraces the results

of a recent study on the effect of three inorganic salts, NaCl, CaCl2 and MgCl2 on some geotechnical properties of a common used clay

soil in impermeable bottom barrier in Kahrizak landfill, the main waste disposal center of the Tehran Metropolitan. Also the effect of

bentonite content by adding different percentage of this special clay mineral, 10 and 20 percent, on these properties was investigated.

Laboratory tests like liquid limit, compaction, 1D consolidation and free swell tests were performed for this purpose. Results indicated

that all of these salts could have a considerable effect on the geotechnical properties of the mixtures. The main reason of such effects is

the changes which occur in diffuse double layer of clay particles.


N. Shariatmadari, S. Saeidijam,
Volume 10, Issue 2 (June 2012)
Abstract

Bentonite-sand mixture is one of the most important candidates for engineering buffer element in nuclear waste repositoriesso
the analysis of its thermo-hydro-mechanical behavior is important for design purposes.An innovative setup of classic oedometer
was used for swelling and compression study at high temperatures in this research. A fully calibration program was utilized to
include high temperature effects on measurements. This research shows that the elevation of temperature from 25 to 90◦C in
1:1bentonite-sand mixture in distilled water reduces free swelling potential and strain about 20 percent. The required time for
equalization of swelling is less in high temperature due to increasing in permeability. Also, the high temperature causes increasing
in compressibility rate and quantity for this buffer. For detection of this effect, XRD analysis showed that an increase in
temperature causes a decrease in basal spacing. So, the particles can come near to each other more than lower temperatures and
the amount of absorbed water in the microstructure of the clay is smaller.The effect of thermal history on behavior of bentonitesand
mixture has been showed and tried to clarify it. At similar stress-temperature states, thermal history causes different
deformation in samples. The highest temperature that bentonite has been experienced, controls its behavior in the next thermal
cycles.


Nader Shariatmadari, Amir Hossein Sadeghpour, Farshid Razaghian,
Volume 12, Issue 3 (Transaction B: Geotechnical Engineering, July 2014)
Abstract

This research shows the results of studies carried out to define and analyze the effect of aging on MSW behavior of Kahrizak Landfill, the biggest landfill in Iran. Studied samples consisted of fresh samples and also aged ones with 5.5, 14 and 21 years of age which were obtained by mechanical excavators in aged burial locations. Analyzing variation in MSW components illustrates that paste fraction of MSW decreases due to aging process while fibers show a rising trend. Also the moisture content and the organic content of MSW reduce below half of the initial values while the degree of decomposition (DOD) increase up to almost 60% after 14 years. These variations over the time are significantly related to the burying methods and environmental condition of burying location. Shear strength behavior of MSW material was analyzed by some CU tests using large scale triaxial apparatus (D=150mm, H=300mm) on remolded MSW specimens. General observations depict that with an increase in strain level, loading rises without any peak point on stress-strain curves. Fresh samples represent the lowest shear strength followed by 21, 14 and 5.5 year-old samples respectively. There is a direct relationship between fiber content and shear strength. Internal friction angle of aged samples decreases in comparison with fresh ones while cohesion has an inverse trend and rises over the time. According to the effect of burying condition on MSW characteristics, it seems that DOD factor is a more appropriate factor than age in order to analyze long-term behavior of MSW.
M. Derakhshandi, H. R. Pourbagherian, M. H. Baziar, N. Shariatmadari, A. H. Sadeghpour,
Volume 12, Issue 4 (Transaction B: Geotechnical Engineering December 2014)
Abstract

In this study, the mechanical behavior of Vanyar dam was evaluated at the end of construction. A two-dimensional numerical analysis was conducted based on a finite element method on the largest cross-section of the dam. The data recorded by the instruments located in the largest cross-section were compared with the results of the numerical analysis at the place of instruments. The settlement, pore water pressure, and total vertical stress were the parameters used for evaluating the dam behavior at the end of construction. The results showed that the settlements obtained from the numerical analysis were in reasonable agreement with the data recorded by the instruments, which proved that the numerical analysis was implemented based on realistic material properties. In addition, the difference between the instruments and the numerical analysis in terms of total vertical stresses was discussed by focusing on the local arching around the pressure cells. Furthermore, the arching ratios were calculated based on the results of the numerical analysis and the data recorded by the instruments. Moreover, the pore water pressures and total vertical stresses, recorded by piezometers and pressure cells, respectively, were the two parameters utilized for evaluating the hydraulic fracturing phenomena in the core. The results demonstrated that the maximum settlement obtained from the numerical analysis was 1 m, which corresponded to 46 m above the bedrock on the core axis. The recorded data in the core axis indicated that maximum settlement of 0.83 m happened 40 m above the bedrock. In addition, maximum pore water pressure ratio recorded by the instruments (Ru =0.43) was more than that obtained from the numerical analysis (Ru =0.26) this difference was due to the local arching around the pressure cells. Furthermore, the arching ratios in Vanyar dam were found to be 0.83 to 0.90. In general, the results revealed that the dam was located on a safe side in terms of critical parameters, including settlement and hydraulic fracturing. In addition, results of the numerical analysis were consistent with those provided by the monitoring system


M. Karimpour Fard, N. Shariatmadari, M. Keramati, H. Jafari Kalarijani,
Volume 12, Issue 4 (Transaction B: Geotechnical Engineering December 2014)
Abstract

Due to the existence of fibrous materials such as plastic fragments, the strength anisotropy of Municipal Solid Waste

(MSW) materials is the main source of differences between their mechanical response in direct shear and triaxial apparatus.

As an extension of earlier research on the mechanical behavior of MSW using a large traixail apparatus, results presented in

Shariatmadari et al. [1] and Karimpour-Fard et al. [2], the current study was programmed and executed. MSW samples were

tested using a computer controlled large shear box apparatus with normal stress levels ranging between 20 to 200 kPa. The

effect of fiber content, fiber orientation, aging and shearing rate on the response of MSW were addressed. The results showed

that shear strength of MSW increases with normal stress, although, in spite of the presence of reinforcement elements in MSW

and unlike the results from triaxial tests, no strain hardening could be observed in their mechanical response. An increase in

the shear strength of MSW was observed with increasing the shearing rate. Increasing the shearing rate from 0.8 to 19

mm/min, enhanced the shear strength of samples from 16 to 27% depending on the shear displacement level. Although, the

same trend was investigated in traixial tests, but lower rate-sensitivity in the mechanical response of MSW in direct shear tests

were observed.

Unlike the results of triaxial tests with aging process, mobilized shear strength level of MSW samples tested under direct

shearing decreased comparing fresh samples. It was also observed that altering the fiber content and their orientation could

affect the mechanical response and shear strength of the MSW. Additionally, there is an optimum fiber angle in MSW which

yields the highest level of shearing strength.


N. Shariatmadari, A.h. Sadeghpour, M. Mokhtari,
Volume 13, Issue 1 (Transaction A: Civil Engineering March 2015)
Abstract

The physical properties of the municipal solid waste (MSW) in Kahrizak Landfill (Tehran, Iran) and its changes due to aging were investigated in this research. A study of the components of the fresh MSW in this landfill showed that more than 60% of it was made from the wastes of foods, fruits, vegetables and organic materials. Next to that, paper/cardboard and plastics, with contributions of 14% and 11%, comprised the greatest parts of the waste materials. Meanwhile, the results obtained from these studies revealed that the contribution of the organic part has been decreased during the last two decade by about 20% while the plastics and paper/cardboard contribution has been increased by the same amount. In order to investigate the effect of aging on the physical properties of MSW, waste samples of 5.5, 14 and 21 years of age were obtained by excavating the aged waste burial regions of this landfill. A study of the changes in the composition of waste materials through aging also revealed that the portion of paste was decreased from 25% to 40% due to the decomposition process, while the contribution of plastics and fabrics was increased up to 200%. Particle size became finer with the mean size being reduced from 70 mm in the fresh wastes to 20 mm in 21-year-old wastes due to the decomposition process. The moisture content of the fresh waste samples was reported to be more than 150%, which was considerably larger than that of other existing landfills. Along with the increase in the age of the waste samples, the moisture content was decreased by as much as one third of the initial value. Furthermore, since the waste mass became more homogeneous by age, the variation of the moisture content was reduced. The organic content of the 14-year-old waste was found to be 20%, which was less than 0.3 of the initial value. Moreover, the variation of the organic content in the waste samples was directly related to the moisture content of the samples with both parameters being reduced to less than one third of the initial value in the older samples. Investigation of the moisture content and the organic content of the aged samples showed that the burial location had a significant effect on the trend of variations. The average density of the fresh waste was measured to be 3.5 and 7.3 kN/m3 after production and burial, respectively. It was found that the average density of the fresh waste grew to about 12kN/m3 as the age was increased.
Nader Shariatmadari, Behnam Askari Lasaki, Hasan Eshghinezhad, Behzad Askari,
Volume 14, Issue 7 (Transaction B: Geotechnical Engineering 2016)
Abstract

The main purpose of this study is to investigate the influence of urban solid waste leachate on the mechanical properties of the soil. Order to provide a more accurate identification of the contaminated soils, Cylindrical specimens of the soil, according to the density curves with different initial conditions (different initial contamination levels) were prepared, then the soil specimens were loaded at different load levels using a direct shear testing equipment and a universal testing machine to apply axial compression on the specimens. By analyzing the results, the stress-strain and failure behavior of the soil specimens containing different percentages of the solid waste leachate was evaluated. The most important result was reducing the mechanical properties of the soil contaminated with different percentages of solid waste. The results of adding lower quantities of leachate, is far more significant compared to the received results from adding higher amounts of leachate.



Page 1 from 1     

© 2019 All Rights Reserved | International Journal of Civil Engineering

Designed & Developed by : Yektaweb